The LECP6 controls NPN or PNP step motors.Motor controller: Step motor (servo/24 VDC), Servo motor (24 VDC) , Compatible with series LEF , Possible to set position, speed & force (64 points) , Screw mounting or DIN rail mounting, PNP DC Step Motor Controller, ELECTRIC ACTUATOR, 0.15 lb
The LECP6 controls NPN or PNP step motors.Motor controller: Step motor (servo/24 VDC), Servo motor (24 VDC) , Compatible with series LEF , Possible to set position, speed & force (64 points) , Screw mounting or DIN rail mounting, PNP DC Step Motor Controller, ELECTRIC ACTUATOR, 0.15 lb
The LECP6 controls NPN or PNP step motors.Motor controller: Step motor (servo/24 VDC), Servo motor (24 VDC) , Compatible with series LEF , Possible to set position, speed & force (64 points) , Screw mounting or DIN rail mounting, PNP DC Step Motor Controller, ELECTRIC ACTUATOR, 0.15 lb
The LECP6 controls NPN or PNP step motors.Motor controller: Step motor (servo/24 VDC), Servo motor (24 VDC) , Compatible with series LEF , Possible to set position, speed & force (64 points) , Screw mounting or DIN rail mounting, PNP DC Step Motor Controller, ELECTRIC ACTUATOR, 0.15 lb
The LECP6 controls NPN or PNP step motors.Motor controller: Step motor (servo/24 VDC), Servo motor (24 VDC) , Compatible with series LEF , Possible to set position, speed & force (64 points) , Screw mounting or DIN rail mounting, PNP DC Step Motor Controller, ELECTRIC ACTUATOR, 0.15 lb
The LECP6 controls NPN or PNP step motors.Motor controller: Step motor (servo/24 VDC), Servo motor (24 VDC) , Compatible with series LEF , Possible to set position, speed & force (64 points) , Screw mounting or DIN rail mounting, PNP DC Step Motor Controller, ELECTRIC ACTUATOR, 0.15 lb
The LECP6 controls NPN or PNP step motors.Motor controller: Step motor (servo/24 VDC), Servo motor (24 VDC) , Compatible with series LEF , Possible to set position, speed & force (64 points) , Screw mounting or DIN rail mounting, PNP DC Step Motor Controller, ELECTRIC ACTUATOR, 0.15 lb
7ND9071en Connector with +24V and GND shall be supplied from external 24V (nominal 24 VDC, range is 18-30 VDC) voltage supply. This supply is powering the converter and the external position sensor. NOTES: 1. Cut the ND9 cable (RC01, RC02 or RC03) and the Position sensor cable to optimal length for your application. Then connect the individual wires as shown in connection diagram. 4.
The MR Configurator2 software will be added to the PC. 5.2 Basic driver set-up for Initial Test Drive Switch on the 24 VDC and 230 VAC power supply to the LECSA driver and wait until the driver display flashes as shown below. 19 - 5.2.1 Start up the Setup software (MR Configurator2TM) Connect the PC and LECSA using the USB cable. Turn on the power of the LECSA.
Additionally, note that the 12 VDC relay does not apply to the auto switch. -12- 11. Pay attention to leakage current. <2-wire type> Current (leakage current) flows to the load to operate the internal circuit even when in the OFF state.
0.8mA or less 100A or less at 24 VDC Indicator LED Red LED illuminates when turned ON.
0.8mA or less 100A or less at 24 VDC Indicator LED Red LED illuminates when turned ON.
Motor: S6,S7,S8] Absolute 18bit encoder (Resolution: 262144 p/rev) Encoder [Type of Motor: T6,T7,T8] [With LECSB-T/LECSS-T] Absolute 22bit encoder (Resolution: 4194304 p/rev) [With LECSC-T] Absolute 18bit encoder (Resolution: 262144 p/rev) specification Type Note 5) No excitation operating type Lock Holding force [N] 27 54 110 Power consumption [W] at 20Note 6) 6.3 7.9 7.9 Rated voltage [VDC
The LECP6 controls NPN or PNP step motors.Motor controller: Step motor (servo/24 VDC), Servo motor (24 VDC) , Compatible with series LEF , Possible to set position, speed & force (64 points) , Screw mounting or DIN rail mounting, NPN DC Servo Step Motor Controller, ELECTRIC ACTUATOR, 0.15 lb
The LECP6 controls NPN or PNP step motors.Motor controller: Step motor (servo/24 VDC), Servo motor (24 VDC) , Compatible with series LEF , Possible to set position, speed & force (64 points) , Screw mounting or DIN rail mounting, PNP DC Servo Step Motor Controller, ELECTRIC ACTUATOR, 0.15 lb
The LECP6 controls NPN or PNP step motors.Motor controller: Step motor (servo/24 VDC), Servo motor (24 VDC) , Compatible with series LEF , Possible to set position, speed & force (64 points) , Screw mounting or DIN rail mounting, PNP DC Servo Step Motor Controller, ELECTRIC ACTUATOR, 0.15 lb
The LECP6 controls NPN or PNP step motors.Motor controller: Step motor (servo/24 VDC), Servo motor (24 VDC) , Compatible with series LEF , Possible to set position, speed & force (64 points) , Screw mounting or DIN rail mounting, NPN DC Step Motor Controller, ELECTRIC ACTUATOR, 0.15 lb
The LECP6 controls NPN or PNP step motors.Motor controller: Step motor (servo/24 VDC), Servo motor (24 VDC) , Compatible with series LEF , Possible to set position, speed & force (64 points) , Screw mounting or DIN rail mounting, NPN DC Step Motor Controller, ELECTRIC ACTUATOR, 0.15 lb
The LECP6 controls NPN or PNP step motors.Motor controller: Step motor (servo/24 VDC), Servo motor (24 VDC) , Compatible with series LEF , Possible to set position, speed & force (64 points) , Screw mounting or DIN rail mounting, NPN DC Step Motor Controller, ELECTRIC ACTUATOR, 0.15 lb
The LECP6 controls NPN or PNP step motors.Motor controller: Step motor (servo/24 VDC), Servo motor (24 VDC) , Compatible with series LEF , Possible to set position, speed & force (64 points) , Screw mounting or DIN rail mounting, NPN DC Step Motor Controller, ELECTRIC ACTUATOR, 0.15 lb