Series VCS Use caution, as there is a danger of being burned if a valve is touched directly. 2. Valves may reach high temperatures when continuously energized. Use caution, as there is a danger of being burned if a valve is touched directly. SOL. AC AC SOL. Without light AC SOL.
V D Approx. 280 D F Approx. 300 F Q Q Class H coil Broken line section C C G 1/2 R R E E A H A H B B 2-P Port size 2-P Port size 2-M, thread depth N 2-M, thread depth N L L K K DIN terminal: D Conduit terminal: T Cable 6.8 to 10 F S Q 27.5 (Q) D F 25 C R C (44) R R E G 1/2 E G 1/2 A H D (S) B B A H 2-P Port size 2-P Port size 2-M, thread depth N 2-M L L K K N.C. dimensions (mm) Grommet:
lubricant that has a shielding effect from ozone.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
Setting Position (mm) D-C7 D-C8 D-C73C D-C80C D-G39 D-K39 D-A33, A34 D-A44 D-B5 D-B6 D-H7l D-H7C D-G5NTL D-H7lW D-H7lF D-H7BAL D-B59W Bore size (mm) A B A B A B A B A B A B A B 20 56.0 31.5 50.0 25.5 55.0 30.5 51.5 27.0 53.5 29.0 53.0 28.5 49.5 25.0 25 56.0 31.5 50.0 25.5 55.0 30.5 51.5 27.0 53.5 29.0 53.0 28.5 49.5 25.0 32 59.5 36.5 53.5 30.5 58.0 35.5 55.0 32.5 57.0 34.0 56.5 33.5 53.0
If fingers are caught in a cylinder, there is a danger of injury due to the strong cylinder output, and therefore caution must be Since the connection between the piston rod and table is a floating structure, there is a maximum table backlash of 0.15 mm in the stroke direction. (Refer to the figure below.) 2.
L 5 to 6 Straight bladed watchmaker screwdriver Switch mounting screw (M5 X 4l) When auto switch D-Y59 A is used B Auto switch L Note) Use a watchmakers screwdriver with a grip diameter of 5 to 6mm to tighten the auto switch mounting screw.Use a tightening torque of 0.05 to 0.1Nm. As a rough guide, tighten the screw an additional 90 after feeling a tighten resistance.
A B Hs A B Hs Hv Hv Hv Hv 12/16/20 12/16/20 Hs Hs 25/32/40 25/32/40 Proper Auto Switch Mounting Position Solid state switch Bore size (mm) 2-color indication solid state switch Reed switch D-A9 D-A9V D-M9 D-M9V D-F9W D-F9WV A B C A B Hs Hv A B A B Hs Hv A B C A B Hs Hv C 15.5 15 20 20 15 19.5 19.5 19.5 19.5 46 46 46 46 18 13 15.5 35.5 42 31.5 42 31.5 12 17 17 22 22 17 21 21 21 21 47.5 47.5
Rz 3.2 or less for sheet surface 500 Compact / Lightweight 2 Port Solenoid Valve VDW30/40-XF Series For Air/Water Dimensions VDW30-G--C4 C6 /One-touch fitting for 4, 6 VDW40-G-/One-touch fitting for 8, 10 C8 C10 36 30 21 23 Approx. 300 32 17.5 20 Approx. 300 27 56 48 10 9 18 21 3 3 21 23 26 A A C4, C6 1 (IN) port C4, C6 2 (OUT) port C8, C10 1 (IN) port C8, C10 2 (OUT) port Dimentions A 3
Note 2) Vibration resistance Conditions when tested with one sweep of 10 to 300 Hz in the axial direction and at a right angle to the armature, in both energized and deenergized states. No malfunction occured when tested.
Calculate the moment of inertia for A and B separately as shown in the figures on the right. A part B part Procedure Calculation Calculation example 1. Check the operating conditions, dimensions of attachment, etc. Operating model: MHY2-16D Opening time: 0.15 s a = 40 (mm) b = 7 (mm) c = 8 (mm) d = 5 (mm) e = 10 (mm) f = 12 (mm) A part a b c B part e f d 2.
As a rule, it should be turned about 90 beyond the point at which tightening can be felt. A B When auto switch D-Y69A is used Auto Switch Hysteresis Auto switches have hysteresis similar to micro switches. Use the table below as a guide when adjusting auto switch positions, etc. Max.
Open the sealed package inside a clean room. These products are packaged in sealed double packaging in a clean room. It is recommended that the inside packaging be opened in a clean room or other clean environment. 2. Flush out the piping. ITV IC ITVH ITVX Connect these products to piping only after it has been flushed and cleaned properly.
Flow Characteristics/Weight Flow characteristics 1 2 (P A) 2 3 (A R) 3 2 (R A) 2 1 (A P) Port size Weight Valve model Grommet C [dm 3/(sbar)] b Cv C [dm 3/(sbar)] b Cv C [dm 3/(sbar)] b Cv C [dm 3/(sbar)] b Cv VT307 VT307V (Vacuum spec. type) VT307E (Continuous duty type) VT307Y (Energy-saving type) VT307W (Energy-saving, Vacuum spec. type) VT307 VT307V (Vacuum spec. type) VT307E
A 1000 1000mm 1000mm 1000 12mm 12mm 16mm 16mm 20mm 20mm A A The length of motor, encoder and lock cables are same.
CAT.ES40-41 A Miniature Regulator Series ARJ310 Improved flow characteristics 0.7 Conditions: Upstream pressure 0.7MPa 0.6 Downstream pressure MPa 0.5 ARJ310-01 0.4 0.3 0.2 ARJ210-M5 0.1 0.0 0 100 200 300 400 500 Flow rate l/min (ANR) Compact and light weight Allows smaller mounting pitch 18.3mm A Accommodates two types of threads Inside: Female thread (M5 x 0.8) Outside: Male thread (1/8
3 m 2 250 L/min PVC 25 A ZS-40-U25 25 A PVC 1 PVC 30 A ZS-40-U30 30 A PVC 1 25 A ZS-40-U25-A 1 M5x80 2 30 A ZS-40-U30-A 1 M5x65 2 PVC 1~2% -12No.PF-OMM0004-D 1 DC+ 2 OUT2 3 DC4 OUT1 M8 IN OUT OUT1OUT2 ON UP ON/OFF SET DOWN ON/OFF -13No.PF-OMM0004-D F.S.( 1~5V F.S.=5[V]1[V]4[V] 1F.S.4[V]10.04[V] 1-5V 1-5V 4-20mA (HYS) ON OFF 90% , () () ,, ,, 10 L/min 10 L ON OFF ON OFF
3 (R) 2 SA VA VH300/400 VM 8 5 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com 6 VR 4 3 VH 1 9 VHS 7 4 (B) 3 (R) 1 (P) 2 (A) 2 VH600 6 5 4 1 7 1 (P) 2 (A) 4 (B) 2 3 (R) Component Parts Material VH200/300/400 Zinc die-casted Aluminium die-casted Description No.
Make sure to clean it once the accumulation of contaminants reaches a thickness of 20 mm or so. w Clean the adsorption surface of the separator by wiping away the accumulated contaminants using a soft rag or the like.