Compact Hydraulic Cylinder BQ2-012 is a set of d and e shown above. 32 to 100 When tightening an auto switch mounting screw, use a watchmakers screwdriver with a grip diameter of 5 to 6 mm.
Proper Mounting Position (Detection at Stroke End) and Mounting Height 32, 40, 50, 63 D-M9/D-M9W/D-A9 D-M9V/D-M9WV/D-A9V Hs B W A A A B (mm) D-A9V D-A9 D-M9 D-M9W D-M9V D-M9WV A B A B Bore size (mm) W Hs A B W A B Hs 32 40 50 63 12 [17] 9 1 12 [17] 9 29 8 [13] 5 3 (0.5) 8 [13] 5 27 16 11.5 1.5 16 11.5 32.5 12 7.5 5.5 (3) 12 7.5 30.5 14 <19> 14.5 4.5 14 <19> 14.5 42 10 <15> 10.5 8.5 (6)
2 20 to 40: Hard anodized w Piston Parallel pin 20 to 40: Aluminum alloy Stainless steel !3 Type C snap ring Heat treated Stainless steel Carbon steel Nickel plated e !4 Lever Exhaust plug A Heat treated Stainless steel Brass Electroless nickel plated r !5 Guide Exhaust filter A Heat treated Stainless steel Polyvinyl formal t !
2 20 to 40: Hard anodized w Piston Parallel pin 20 to 40: Aluminum alloy Stainless steel !3 Type C snap ring Heat treated Stainless steel Nickel plated Carbon steel e !4 Lever Exhaust plug A Heat treated Stainless steel Electroless nickel plated Brass r !5 Guide Exhaust filter A Heat treated Stainless steel Polyvinyl formal t !
D Lever type models Caution RS (D) 32/40/50-L RS (D) 32/40/50-B RS (D) 32/40/50-C RS (D) 32/40/50-D RS (D) 32/40/50-E Mounting base 1. Do not allow a pallet to collide with the cylinder when the lever is upright.
conductive object is moved through a magnetic field, an electromotive force will be generated.
Pressure holding VXH It is not usable for an application such as holding the pressure inside of a pressure vessel because air leakage is entailed in a valve. VXF 5. When the conduit type is used as equivalent to an IP65 enclosure, install a wiring conduit etc. VX3 VXA 6.
Built-in silencer, Direct exhaust [-S] When ordering assemblies incorporated with a manifold, add suffix S to the manifold No. This is an exhaust port on a top the manifold end plate. The builtin silencer exhibits an excellent noise suppression effect.
-X 1 to 349 20, 25, 32 Applicable stroke (mm) 5 to 345 40 to 80 2025 to 345 100 Part no.: MLGPM20-39-F A 1 mm spacer is installed in MLGPM20-40-F . Dimension C is 77 mm.
6 Slide bearing Ball bushing Spacer Pivot Chromated Heat treated/Electroless nickel plated Chromium molybdenum steel Nickel plated Chromium molybdenum steel 9-11-23 23 Series MLGP Construction: 40 to 100 Series MLGPM Series MLGPL !2!1#4 u @1 $0w #6 #1 #2y $0 #7 @2 q !0!4 r@4 #8 $1 e @1 @3t #3 !5 @8 B' @9 @0 A' A A' A B !6 !3 #0 40 to 63: Over 100 stroke !
Refer to the Auto Switches Precautions for using with an auto switch. 14.When a cylinder is used in a clamping, suspending, or lifting mechanism There is a danger of workpieces dropping if there is a decrease of thrust due to a drop in circuit pressure caused by a power outage, etc.
Provide shading in an environment where the product is exposed to the sunlight. 4. Block off heat radiation in an environment where a heat source is at a close distance. Block off heat radiation with a cover if a heat source is at a close distance because the temperature of the product can rise to exceed the operating temperature range due to radiation. 5.
Provide shading in an environment where the product is exposed to the sunlight. 4. Block off heat radiation in an environment where a heat source is at a close distance. Block off heat radiation with a cover if a heat source is at a close distance because the temperature of the product can rise to exceed the operating temperature range due to radiation. 5.
11.5 18.5 23 B 12.5 14.5 13.5 19 B 9 11 10 15.5 B 7 9 8 13.5 A 14 12 19 23.5 B 13 15 14 19.5 A 14.5 12.5 19.5 24 B 13.5 15.5 14.5 20 B 7.5 9.5 8.5 14 B 10.5 12.5 11.5 17 B 7 9 8 13.5 20 25 32 40 Note) When setting an auto switch, be sure to check its operation before adjusting.
Note 6) For an actuator with lock, add the power consumption for the lock. 19 -
2.2 How to Order 20 -
2.3 Construction LEFS
Hs B A Reed switch Solid state switch D-A9 V D-M9 V D-F9 WV 20, 25 Hs B A 32, 40, 50, 63 Figures in the table below are used as a reference when mounting the auto switches for stroke end detection. In the case of actually setting the auto switches, adjust them after confirming their operation.
The purpose of an air cushion is not to reduce the speed of a piston as it nears the stroke end.
When a driven object is stopped, ensure the impact force of the object being transferred to the floating joint is prevented by using a cylinder with a built-in cushion mechanism (rubber cushion or air cushion). To stop the cylinder at the intermediate position, use an external shock absorbing mechanism such as a shock absorber.
A Moment of Inertia The moment of inertia indicates the difficulty of turning an object, or conversely, the difficulty of stopping an object which is turning. Since there is a limit to the kinetic energy allowed in a rotary actuator, the limit value of the rotation time can be found by finding the moment of inertia. How to find the moment of inertia is explained below.
Temperature Data A or B = Series IDUS: Data A Series IDFS: Data B Air pressure Data C = 2 Calculate corrected air flow by using A or B and C. Corrected air flow = (Air flow) (Data A x Data C) Corrected air flow = (Air flow) (Data B x Data C) 3 Select a model having an air flow capacity that is higher than the corrected air flow.