Cylinder with Turntable Series MGT ø63, ø80, ø100 1 Mounting of Auto Switch When mounting an auto switch, insert it into the cylinder's switch groove from the direction shown in the figure below. After setting it in the mounting position, use a flat head watchmakers screwdriver to secure it with the mounting screw which is included.
Note 3) An optional specification for special wiring is available to increase the maximum number of stations.
When the gripping point distance becomes large, the finger attachment applies an excessively large load to the finger sliding section, causing excessive play of the fingers and possibly leading to premature failure.
When the gripping point distance becomes large, the finger attachment applies an excessively large load to the finger sliding section, causing excessive play of the fingers and possibly leading to premature failure.
This is due to an offset load from the weight of the rod. Note 2) Refer to precautions on page 18 regarding lubrication. Note 3) Control low speed actuation with differential pressure and a speed controller, etc. (Refer to recommended circuit examples for further details.)
If operated with the work piece gripping point beyond the indicated ranges, an excessive offset load will be applied to the sliding section of the fingers, which can have an adverse effect on the service life of the product.
Also, BBA2 is included when an auto switch alone is shipped.
Precautions Plug a connector in or out vertically, never at an angle. Applicable cable O.D.: 3.5 to 7 (Reference) 0.5 mm2 2 core and 3 core wires equivalent to JIS C 3306 DC 24V 48V Caution No.2() Black () No.1(+) 1. Since this valve has slight air leakage, it can not be used for holding vacuum (including positive pressure holding) in the pressure container.
S Couplers KKA Series Stainless steel type RoHS KQ2 KQB2 KS KX KM KF M Body material: Stainless steel 304 Seal material: Fluororubber (Special FKM) H/DL L/LL KC Both plug and socket have an integral check valve. Available with and without check valves depending on the operating conditions. KK KK130 Reduces liquid dripping when the plug and socket are uncoupled.
Precautions Plug a connector in or out vertically, never at an angle. Applicable cable O.D. 3.5 to 7 (Reference) 0.5 mm2 2 core and 3 core wires equivalent to JIS C 3306 Caution DC 24V 48V Black () 1. Since this valve has slight air leakage, it can not be used for holding vacuum (including positive pressure holding) in the pressure container.
18 M18 x 1.5 35 63 32 20 46 18 M18 x 1.5 35 80 37 25 51 22 M22 x 1.5 40 100 37 30 52 26 M26 x 1.5 40 40 Auto Switch Specifications Series CHQWB Auto Switches: Proper Mounting Positions and Mounting Heights for Stroke End Detection 20 32 to 100 D-A7 D-A80 Approx.
G1/2 Electric conduit 4 x M8 x 1.25 depth12 Female thread for rear mounting At accessory H: (with external scale plate) E 100 60 44 46 8
Refer to p1.11-46 for external pilot specification. Combination of external pilot and perfect interface is not possible. When specifying more than one option, indicate symbols alphabetically.
Note 5) For command pulse input with an open collector method.
Do not apply an impact load or strong vibration while the lock is activated. If an external impact load or strong vibration is applied to the product, the lock will lose its holding force and damage to the sliding part of the lock or reduced lifetime can result.
Both input and output sizes are shown for an input / output unit. In / Out size Input data "--" is displayed for an output unit. Displays input data value which is sent to an input unit or input / output unit. Output data "--" is displayed for an input unit.
An Alarm is generated depending on the set value of the Return to origin parameter.
An EXH block base assembly is used in the blocking position when ordering an EXH spacer incorporated with a manifold. However, do not order an EXH block base assembly because it is attached to the spacer. When separately ordering an individual EXH spacer, separately order an EXH block base assembly because it is not attached to the spacer.
Do not use in an environment laden with oil or chemicals. Consult with SMC if auto switches will be used in an environment laden with coolants, cleaning solvents, various oils, or chemicals.
They do not guarantee an actual fixed range (expect approximately 30% dispersion).