ITVH As a countermeasure, install an aftercooler, air dryer or water separator, etc. 3. If large amounts of carbon dust are generated by the compressor, it can accumulate inside this product and cause a malfunction (air leakage etc.). Fluid Supply Warning 1. Compressed air or nitrogen can be used as a fluid. 2.
Perform inspections on a regular basis as necessary, such as at the beginning of an operation, to make sure that the mechanical valve operates properly. Failure to observe this precaution could lead to unsafe operation, such as unintended operation or malfunction.
As a guide, an acceptable tightening level is reached by tightening the screw an additional 90 degrees (1/4 turn) from the point at which the screw is snug. (Refer to Figure 3.)
The following is given using OUT1 as an example. The descriptions for OUT2 are the same as those for OUT1, under the conditions that [n_1] and [n_2] should be replaced by [n_3] and [n_4], [P_1] and [P_2] should be replaced by [P_3] and [P_4] and [H_1] should be replaced by [H_2]. Input a set value for pressure to perform switch output.
If driving a load such as a relay that generates a surge voltage, use an auto switch with built-in contact protection circuit or use a contact protection box. 3.
Series Dimensions: Universal Type Seal method: Sealant For R, NPT thread Applicable tubing O.D. d D3 W1 AS-F AS-F D1 Y TMH ASD L4 L3 M AS AS-FE A L5 D2 KE AS-FG AS-FP L2 L1 T H (Width across flats) AS-FM AS-D Metric Size [mm] AS-T Model d T H D1 D2 D3 L1 L2 L3 L4 L5 A M W1 Y Weight [g] Unlocked Locked Unlocked Locked AS231FS1-01-23 (S) 3.2 ASP 13.3 24 17.5 36 43.9 42.4 40.8 39.3 13.3 20
Avoid locations where a dryer could draw in high temperature air that is discharged from an air compressor or other dryer. Avoid locations subjected to vibration. Avoid possible locations where the drain can freeze. Use the air dryer with an ambient temperature lower than 104F (40C). Avoid installation on machines for transporting, such as trucks, ships, etc.
(-XC6) Caution Other specifications are the same as the standard model. Dimensions q Do not use the air cylinder as an air-hydro cylinder. This will cause an oil leak. w Install without twisting the bellows. If the cylinder is installed with its bellows twisted, it could damage the bellows.
There may be the case it will vary substantially depending on an ambient environment. (n 2) 2 20 + 55 D-A59W 30 (n = 2, 4, 6, 8 ) Note 1) (n 2) 2 20 + 40 D-Z7/Z80 20 (n = 2, 4, 6, 8 ) Note 1) D-A5/A6/A59W cannot be mounted to 40, 50. Note 1) When n is an odd number, an even number that is one larger than this odd number is used for the calculation.
In the case of adsorption on a small work piece of only a few millimeters, if an ejector is selected which has a high suction flow rate, the pressure difference when adsorbing and releasing the work piece is small. Since setting of the vacuum switch may become difficult, an appropriate ejector should be selected. 5.
Real-time switch output, accumulated switch output, or accumulated pulse output can be selected as an output type.
Full access to this twoway databus is as simple as wiring into 2 terminals and snapping onto the yellow ASi Data Cabling. Control and output is further increased by transforming the Intelligent Valve Island into an Intelligent Node System, working within the ASi Network Domain.
The cushion effect (smooth start-up, soft stop) cannot be obtained in an intermediate stop or a return from an intermediate stop using an external stopper, etc.
Never remove valve at an angle.
2.5 to 6 6 to 20 20 to 40 40 to 63 63 to 100 AS13l1F AS13l1F AS23l1F AS33l1F AS43l1F / 1 8, / 1 4 / 1 4, / 3 8 / 1 2 Elbow (Metal Body) M5 6 to 20 20 to 32 20 to 40 40 to 63 63 to 100 AS12l1 AS22l1 AS22l1 AS32l1 AS42l1 / 1 8 4.1-7 / 1 4 / 3 8 / 1 2 In-line 6 to 20 20 to 32 20 to 40 40 to 63 63 to 100 AS1001F AS2001F AS2051F AS3001F AS4001F 4.1-9 Dual Speed Controller 6 to 20 20 to 32 20
Note 2) When used as a common external pilot, select the internal pilot specification as an applicable valve. Note 3) Gasket and mounting bolts are equipped.
-l06 to 10 ALD900-l12 to 20 D.P.
Choose the desired connecting block with the OK key Function Blocks (FB) are connected by joining an output pin to an unused input pin. The arrow is pointing to the output pin. The output pin is always shown on the right side of the function blocks. Unused Input pins are shown as > while used input pins show as a solid triangles.
Lightning surge countermeasures should be applied directly to system components as necessary. 2. Our pressure switches do not have an explosion proof rating. Never use in the presence of an explosive gas as this may cause a serious explosion.