PSE200 Do not touch the LCD indicator. Do not touch the LCD indicator face of the pressure switch during operation. Static electricity can change the readout. 3. Pressure port Do not introduce wire, needles, or similar objects to the pressure port as this may damage the pressure sensor and cause malfunctions. 1. Do not use in an area where surges are generated.
However, components that are combined together during the distribution process do not have a label on them. 4.
M9N M9NV 3-wire (NPN) IC circuit 5 V, 12 V M9P M9PV 3-wire (PNP) M9B M9BV 2-wire 12 V 24 V Relay PLC Yes Grommet F9NW F9NWV 3-wire (NPN) 5 V, 12 V IC circuit Diagnostic indication (2-color indication) F9PW F9PWV 3-wire (PNP) F9BW F9BWV 2-wire Lead wire length symbols: 0.5 m Nil (Example) M9N 3 m L (Example) M9NL 5 m Z (Example) M9NZ 12 V Solid state switches marked are produced
switch Reed switch 12 V Relay PLC Yes Grommet 24 V 5 V, 12 V IC circuit Diagnostic indication (2-color indication) 12 V 5 V A96V A96 IC circuit Yes Grommet A93V A90V A93 A90 100 V Relay PLC 12 V 24 V 2-wire No 100 V or less IC circuit Lead wire length symbols: 0.5 m Nil (Example) M9NW 1 m M (Example) M9NWM 3 m L (Example) M9NWL 5 m Z (Example) M9NWZ Solid state auto switches marked
CEU5mm-m Multi-counter For details, refer to page 12. 1 LATH3-m Counter cable For details, refer to page 11. 2 Controller setup kit For details, refer to page 12.
Refer to Best Pneumatics vol.8 (CY1 series model selection method) for details. 12-REA40 12-REA40 6 2.1 12-REA50 12-REA50 8 3.4 12-REA63 12-REA63 8 3.4 3. Throttle type speed controllers are recommended for speed adjustment, as shown in the table below. Recommended speed controller Model 5. Do not scratch or gouge the external surface of the cylinder.
No.9 Only the solenoid valve/output block LEDs do not light up Refer to trouble No.3 Refer to trouble No.10 The red SI unit MS_LED lights up The inputs that are beyond the maximum point number do not operate The input block does not operate normally Refer to trouble No.4 Refer to trouble No.11 The red SI unit MS_LED flashes Refer to trouble No.12 The green SI unit MS_LED flashes The Input
Voltage symbol 24 VDC V100-61-3-05 DC 24 VZ 12 VDC V100-61-3-06 DC 12 VZ 100 VAC V100-61-2-01 100/110 VZ 200 VAC V100-61-2-02 200/220 VZ 110 VAC V100-61-2-01 100/110 VZ 220 VAC V100-61-2-02 200/220 VZ 240 VAC V100-61-2-07 240 VZ If an AC specification without DIN Terminal (DO) is selected, always use a DIN connector with surge voltage suppressor as the connector.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300 m/s2 or more for reed switches and 1000 m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
Do not use the product in an environment subject to a temperature cycle. It will cause failure of the electric actuator or its peripheral devices. Do not use the product in a place where surges are generated.
Do not scratch any surface with the screwdriver. 2) Piston seal (Fig. 12, ) Mount with care not to twist the piston seal. Apply grease to the seal groove and outer circumference by rubbing grease into them as shown in Fig. 13. 3) Tube gasket (Fig. 12, ) Mount with care not to twist the tube gasket. A little less than 1mm Fig13. Rod seal Fig14.
Do not drop or bump. 5. Do not allow short circuit of loads.
RR CL + Stroke RR 15 6.5 12 8 6 10 A + Stroke 18 8 16 10 9 16 20 10 20 10 10 20 20 18 36 12 10 25 22 18 36 12 10 28 8 Series MQQ Accessory Dimensions Rod end thread adapter Rod end nut d NN MM Rod D C C B H E F A B H Applicable bore size (mm) Applicable bore size (mm) Part no.
Do not turn the balance adjusting screw until the condition is decided. 12: If the actuator angle is outside of 50+/-2%, the LCD displays bars (-). Do not rotate the balance adjusting screw until verification is complete. 13: Bars (-) continue to display until verification is complete. If the button is pressed before verification, the LDC displays a busy message (bUSy).
Do not use under such conditions. (Refer to the specifications.) Please consult with SMC when using a fluid other than compressed air (including vacuum). We do not guarantee against any damage if the product is used outside of the specification range. (2)Do not disassemble the product or make any modifications, including additional machining.
Caution on operation Do not Do not Do not Do not Warning D o Do not Do not D o D o D o SMC Corporation This product aims at application for common factory automation equipment. Do not use LZC for machinery and devices (1) that directly concern human life or those which malfunction or failure could cause serious damage.
Precautions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate or set with wet hands. This may lead to an electric shock. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Do not wire with power lines or high voltage lines. Wire separately from power lines or high voltage lines, avoiding parallel wiring or wiring in the same conduit with these lines. Control circuits, including switches, may malfunction due to noise from these other lines. 5. Do not allow short circuiting of loads.
, 16 85 + 40 (n 4) 2 n = 4, 8, 12, 16 90 + 40 (n 4) 2 n = 4, 8, 12, 16 105 + 40 (n 4) 2 95 + 40 (n 4) 2 n = 4, 8, 12, 16 n n = 4, 8, 12, 16 2 (Different sides and same side) With 1 10 65 75 80 90 D-Y69/Y7PV D-Y7WV n 90 + 30 (n 4) 2 80 + 30 (n 4) 2 n = 4, 8, 12, 16 10 + 30 (n 2) 2 n = 2, 4, 6, 8 65 + 30 (n 4) 2 n = 4, 8, 12, 16 75 + 30 (n 4) 2 n = 4, 8, 12, 16 n = 4, 8, 12, 16 2 (