DOC1023894

Specifications 10 4. Product outline 10 5. Troubleshooting 11 6. Construction and parts 1112 1 - Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.

Guide Cylinder

Otherwise, the guide parts has twisted and lead to a malfunction. -10- 10) Mount in locations where maintenance will be easy.

Regulator Valve

Option Rated voltage Voltage symbol Part no. 100 VAC 100V VK300-82-2-01 110 VAC 110V VK300-82-2-03 200 VAC 200V VK300-82-2-02 Note) When requiring a gauge different than that mentioned above, specify the model number. 220 VAC 220V VK300-82-2-04 Option is packed with it.

Process Pump

If the total lifting height is required instead of the discharge pressure, a discharge pressure of 0.1 MPa corresponds to a total lift of 10 m. Selection procedures: 1. First mark the intersection point for a discharge rate of 27 L/min and a discharge pressure of 0.25 MPa. 2. Find the pilot air pressure for the marked point.

VY511, VYU5

) Fittings (4 pcs.): DL10-02 P 250 700 200 600 176 Conditions Supply air pressure: 0.5MPa Load ratio: 50% 90 elbow: 4 pcs.

IDX-OM-P023E

The fluctuation of the power supply voltage should be kept within +/-10% of the rated voltage. Refer to 5.2 Reset of protective equipment and reset the protective circuit. The fluctuation of the power supply voltage is too large. When the cooling water is not flowing, the compressor for refrigeration has stopped with the lamp lit up. Water-cooled condenser is dirty.

SJ1000/2000/3000 Series

[Load: 10 N or less] Turning without pushing can cause damage to the manual override and trouble such as air leakage, etc. Manual Override Switch Operation For manual override operation, move the manual override switch to a position where letters A and B can be seen.

Precision Regulator

Bracket, gauge and switch assembly (optional) 10 6. Panel mounting 11 7. Troubleshooting 12 8. Dimensions 13 to 14 -1- Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.

Bacteria Removal Filter

Fastening torque recommended: 10+/-2Nm 5-6. Start of operation Before actual operation, confirm there is no leakage. If there is leakage, remove the element after stopping the operation. Clean the seating surfaces, check and replace the O-ring and tighten the cover. -10- Doc. No. SF-OMZ0013-B 6. Dimensions -11- Doc. No. SF-OMZ0013-B Revision history Rev.

IR30-OM00013

-01 G43-P10-N01-X30 02:1/4 03:3/8 04:1/2 Rc FG NNPT 00.010.2MPa 10.010.4MPa 20.010.8MPa PRECI SI O N REG U LATO R I R302BG No.

VFR2000-OMM0001

No.VFR2000-OMM0001 5 VFR2000 / / / / -2,3 -4 -5 -5 -6 -6 -6 -7 -7 -7 -8 -9 -9 -9 -10 3 -10 -10,11 DIN / -11 -11 -12,13 -14,15 -1No.VFR2000-OMM0001 ISO/IEC) (JIS) 1) 2 *1) ISO 4414: Pneumatic fluid power -General rules relating to systems ISO 4413: Hydraulic fluid power -General rules relating to systems IEC 60204-1: Safety of machinery -Electrical equipment of machines

VEX-OMV0001

(1) (2) (3) 2(A)3(R)() (4) (5) 3(R) (6) 2(A)() (7) (8) (9) (10) (11) (12) 1 (ISO VG32) (13) 3(R) (14) (15) (16) (17) (18) (19) (20) (21) (22) 1. 2. 3. 4. 5. 6. 7. * 12 VEX-OMV0001 : VW 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL http://www.smcworld.com Note: Specifications are subject to change without prior notice

EX9-OEx_PE.eng

Rated load current Max. 62 mA (1.5 W) / point Max. 0.5 A (12 W) / point -10 to +50 oC (solenoid valve type) Operating ambient temp. Power block (EX9-PE1) NOTE Specifications Item When conformity to UL is necessary the SI unit must be used with a UL1310 Class 2 power supply.

PF2M7.eng

PF2M7-B.eng:PF2M7-B.eng.qxd 21/04/09 14:02 1 Before Use Digital Flow Switch PF2M7## Wiring Wiring of connector Connections should only be made with the power supply turned off. Use separate routes for the product wiring and any power or high voltage wiring. Otherwise, malfunction may result due to noise.

CG1-SMV13_en

URL : http// www.smcworld.com (Global) http// www.smceu.com (Europe) 'SMC Corporation, Akihabara UDX15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101 0021 Specifications are subject to change without prior notice from the manufacturer. 2016 SMC Corporation All Rights Reserved. Template DKP50047-F-085D Avoid repeating sudden charges and discharges of the air tank.

VF1000-OMP0001

-12 DXT031-44-1 M4X39.5 DXT031-30-2 VF330 VF333 DXT155-25-1 VF340 VF343 VF350 AXT620-32-1 M4X48 DXT156-9-8 VF520 DXT156-9-1 VF544 10 VF1000-OMP0001 R () P 11 VF1000-OMP0001 No. 1ISO VG 32 (R) 1. 2. 3. 4. 5. 6. 7. 12 VF1000-OMP0001 Revision history 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL http://www.smcworld.com Note: Specifications

3/5 Port Solenoid Valve

For example, install a ventilation opening, etc. in order to prevent pressure from increasing inside of the confined area and to release the heat generated by the valve. 10. Extended periods of continuous energization If a valve will be continuously energized for an extended period of time, the temperature of the valve will increase due to the heat generated by the coil assembly.

Pressure Switch/Reed Switch Type

2 q Magnet 9 Piston 10 POM Seal piston 11 NBR 1/8 15 23 Scale plate 12 PC Wiring Warning Mounting Warning Pressure Source Warning 1. 1. 1. Connect load before connecting with power source. The switch will break instantly if no load is connected. Make the wiring length as short as possible.

ISE7xG.eng

Piping Piping specification: -02 and -N02 After hand tightening, tighten the fitting using a spanner on the flat surfaces of the fitting. The tightening torque must be 8 to 12 Nm.

ISE70_71-AB.eng

Piping specification: -02 and -N02 After hand tightening, tighten the fitting using a spanner on the flat surfaces of the fitting. The tightening torque must be 8 to 12 Nm.