CYV_EN If load (pressure) exceeds the allowable level, the magnet coupling may come off and the slide table may drop. Pay great attention to the load and pressure control. 3. Do not use the cylinder when the magnet coupling is displaced.
In such cases, human injury may occur, e.g. by hands or feet getting caught in the machinery, or damage to the machinery itself may occur. Therefore, the machine should be designed to operate smoothly and to avoid such dangers. 2) If there is a chance that the product will pose a hazard to humans, install a protective over.
If the countermeasures above are not effective, there may be a problem with the valve. In that case, stop using the valve immediately. If any of the examples below are applicable, there may be an internal problem in the valve. In that case, stop using the valve immediately. The voltage used was not the rated voltage. The oil supplied was not the specified type.
As the clip may fly out, pull it slowly as holding it with a hand. 3) Pull out the mounted One-touch fitting. Procedure 1) Presence of O-ring. (If dust or particles are remained on the O-ring it may cause air leakage. Therefore take measures to prevent them from attaching on the O-ring.
The following procedures are an example of how a test may be performed. It is intended as an overview and not as an all inclusive description. 1) Rotate the adjustment wheel counterclockwise (DECR) completely to relieve spring force.
Cutting particles and fluids may remain and they cannot be removed completely. Such foreign objects may stick to the workpiece.
Since the mechanically jointed rodless cylinders have a unique seal structure, slight external leakage may occur. Controlling intermediate stops with a 3-position valve cannot hold the stopping position of the slide table (slider). The speed at the restarting state also may not be controllable.
As an example, for a travel of 100 (mm) Travel distance of the actuator per 1 pulse = 0.001 (mm) *1 100 (mm)/0.001 (mm) = 10 (pulse) If the stroke end signals (LSP, LSN) are not turned ON, an alarm may occur.
The damage to the pressure switch may have been caused by the operating environment (network construction, etc.). Consult with SMC separately to obtain countermeasures.
The damage to the pressure switch may have been caused by the operating environment (network construction, etc.). Consult with SMC separately to obtain countermeasures.
The damage to the pressure switch may have been caused by the operating environment (network construction, etc.). Consult with SMC separately to obtain countermeasures.
The product may be damaged if a voltage over this value is applied. (The withstand voltage is not the supply voltage used to power the product.)
The damage to the pressure switch may have been caused by the operating environment (network construction, etc.). Consult with SMC separately to obtain countermeasures.
Even after the power is turned off, there can still be residual heat in the product, which may cause burns.
It may cause the auto drain operation to fail. Air Supply Warning 1) Use clean air. Do not use compressed air containing chemicals, organic solvent, synthetic oil or corrosive gas as it may be cause of breakage of components or operation failure. 2) Air containing too much moisture may deteriorate the performance.
It may cause the auto drain operation to fail. Air Supply Warning 1) Use clean air. Do not use compressed air containing chemicals, organic solvent, synthetic oil or corrosive gas as it may be cause of breakage of components or operation failure. 2) Air containing too much moisture may deteriorate the performance.
[F11] Display resolution setting completed : It may not be possible to change the resolution depending on the unit of pressure selected. Setting of display resolution may not be available depending on the units for display. Part No.
As the clip may fly out, pull it slowly as holding it with a hand. 3) Pull out the mounted One-touch fitting. Procedure 1) Presence of O-ring. (If dust or particles are remained on the O-ring it may cause air leakage. Therefore take measures to prevent them from attaching on the O-ring.
If it uses turbine oil in place of fluids for cylinder, it may result in oil leakage. 4. The oil stuck to the cylinder is grease. 5. The base oil of grease may seep out.
Discharge volume may vary depending on the fluid and piping conditions. After mounting is complete, perform appropriate functional inspections. 3. Do not use this product in a location where it will be subject to vibration or impact. The dispense volume may become unstable in the presence of vibration at the pump or piping. 7.