AS-FG/ASD-FG of 0.5MPa and a temperature of 20C. 7 Series AS-FG How to Order AS 200 1 F G 06 Body size Applicable tube outside diameter Metric size Inch size 100 200 205 300 400 M5 standard 1/8 standard 1/4 standard 3/8 standard 1/2 standard 1/8" 5/32" 3/16" 1/4" 5/16" 3/8" 1/2" 01 03 05 07 09 11 13 3.2 4 6 8 10 12 23 04 06 08 10 12 With One-touch fitting Use a 1/8" tube.
The cancel cap holds the lever horizontally allowing a pallet to pass.
Detaching To detach a socket from a connector, pull out the lead wire while pressing the sockets hook with a stick having a thin tip (approx. 1 mm). If the socket will be used again, first spread the hook outward. Connector assembly with protective cover Connector assembly with protective cover enhances dust protection.
HS A A A B 19.5 (27.5) 19.5 (27.5) 20.5 (28.5) 23 (32) 27.5 (39.5) 27.5 (39.5) A HS A HS B 15 (22.5) 15 (22.5) 15.5 (23.5) 18 (27) 22.5 (34.5) 22.5 (34.5) 31 (45) 31 (45) 30 24.5 27 27.5 29 24 27 25.5 27.5 20 30 27 27 27.5 29 24 29.5 25.5 30 25 31 30.5 28 28.5 30 25 33 26.5 33.5 32 35.5 35 32.5 33 34.5 29.5 37.5 31 38 40 43 40.5 40 40.5 42 37 43 38.5 43.5 50 43 47.5 40 40.5 42 37 50 38.5
When a filter element is used repeatedly, clean it with air blow or wash it with a neutral detergent. (For 40 m, For 80 m) Check the condition of the element and replace the element with a new one when the specifications are not satisfied.
When a layout becomes complicated, please indicate it on a manifold specification sheet.
Enclosure Note) Impact resistance: No malfunction when tested with a drop tester in the axial direction and at a right angle to the main valve and armature, one time each in both energized and deenergized states.
Displacement at the section indicated by the arrow when a load is applied to this section with the slide table fully extended. Displacement at "A" when a load is applied to "F" with the slide table retracted.
Applicable pad 4020W/5020W/6020W/8020W Applicable pad 3507W/4010W/5010W/6010W Applicable pad 4030W/5030W/6030W/8030W A-A A-A A-A (5) (5) (5) 14.8 8.8 6 1.5 A A A A A A 2 0.8 2 3.5 4 4 15 15 30 3 5 5 3 5 3 0.8 0.8 8.4 12.8 20.4 Note) R part has to be smooth with no corners.
A parallel keyway is used instead of chamfer for size 40. +5 0 +5 0 CRJ +4 0 = Max. = 200 +4 0 = Max. = 110 CRA1 ) ) ( ( e e g g n End of rotation n a a r r n n o CRQ2 o End of rotation ti ti a a t t o o R R MSQ (90) MRQ Chamfer Chamfer (Start of rotation) (Start of rotation) (45) A port B port A port B port D(Top view from long shaft side) Start of rotation is the position of the chamfer
Single vane type Double vane type +4 0 9 0 a a r r n n e n n g g g o o e e n i i t t 1 2 a a a 8 7 r t t 0 -5 +4 0 o o 0 0 n R R +4 0 +4 0 o 0 i 0 0 t a 9 1 t o e e R g g n n a a r r n n o o i i t t a a Chamfer Chamfer t t o o Chamfer A port B port Chamfer A port Chamfer R R A port B port B port A port B port A port B port For size 40 actuators, a parallel keyway will be used instead
For the angle adjusting type, angle adjusting screws are mounted to the left cover. of e g k n e ra y w n a io y Angle adjusting screw Angle adjusting screw at 1 ot 8 0 n R io ct e r di g in st u dj n A o a n ti g c e e l e gl ir d a n d g A j u n s ti ti s n u g j d a d ir e e R R l g c 0 0 n ti ot ot o A 8 8 n 1 1 at at y y io io a a n n w w r r y y a a e e n n k k g g of of e e Angle
A 2 A Power supply (Output) 24 VDC +10/-5%, 24 VDC +10/-5%, 8 A DC24 V +10/-5%, 4 A 2 A Enclosure IP67 (With manifold assembled) 1 Environment Operating temperature range -10 to 50 oC Storage temperature range -20 to 60 oC Operating humidity range 35 to 85%R.H.
D C o n s t a n t M O D E < 0 . 0 s e c When 0 is set, this function becomes invalid. 8-8 Operation 7. Heating/Cooling Ratio Setting range : 10 to 999% Min. increment : 1% H e a t i n g / C o o l i n g R a t i o M O D E < 2 0 0 % Indicated content : Heating/cooling gain ratio(Ex. : 200%) Function: Sets output ratio of cooling to heating to compensate difference of gain between them. 8.
LifeNote) Response time Model SQ1000 12 ms or less 200 million cycles For applications which demand high speed, high frequency, long life and a precise response time.
Therefore, internal parts of a cylinder other than rod seal are not replaceable. 2. Use caution to the popping of a retaining ring. When replacing rod seals and removing and mounting a retaining ring, use a proper tool (Retaining ring plier: Tool for installing a type C retaining ring).
N.O. 1 (P) 3 (R) 1 (P) 3 (R) a c e d a c e d (A) (A) 2 2 g g 3 (R) 1 (P) 3 (R) 1 (P) b b f f Component parts Replacement parts Note Zinc die-casted No.
Rotate the pin 30 to the right with a wooden implement such as the grip of a wooden hammer or a resin stick without scratching.