ITV Pressure may fluctuate when air is consumed at the output side. ([Example] Tank) Proof pressure test SUP.
No.0.8 L1 L3 L2 L3 (L4) No.0.8 H 2 H 2 H 2 L1 M1 M1 M1 D Pad side Pad side Pad side ZP2V-A01ZP2V-AN1ZP2V-AG1ZP2V-A5ZP2V-A8Vacuum generator side D Vacuum generator side M2 M2 L3 L2 H 1 Vacuum generator side L2 L3 3 H 1 M2 H 1 (L4) (L4) No.0.8 No.0.8 (L4) No.0.8 H 2 H 2 L1 L1 L1 H 2 M1 M1 M1 Pad side Pad side Pad side ZP2V-B01ZP2V-BN1ZP2V-BG1ZP2V-B5ZP2V-B61 The place at the vacuum generator
L1 8 L2 4 x 9 (for M8 mounting) 2 port valve 3 port valve Cleaning valve + Gate valve < >: Pilot port is C6.
AMG should be installed at the highest pressure and as far away as possible from the compressor. Particle and oil filter, plus pressure regulation if required, should be installed downstream of AMG. The element design produces negligible pressure drop. Note: AMG does not remove water vapour & air leaving AMG is 100% saturated. Where dehumified air (ie.
MXJ8 500 4 13 12 MXJ8 The above value represents the applicable load at the position where the moment does not work at the time of stop. Factors such as impact, etc. are not in consideration with the value.
Note 2) Vibration resistance Conditions when tested with one sweep of 10 to 300Hz in the axial direction and at a right angle to the armature, in both energized and deenergized states Impact resistance ...Conditions when tested with a drop tester in the axial direction and at a right angle to the armature, one time each in energized and deenergized states Characteristic Specifications Note
Turn it in the counterclockwise direction at 90 to lock the manual. Turn it right to release.
The position adjustment of the auto switch should be performed at two positions; a position determined by the stroke and a position after the backlash movement (by 2 mm). When a 2-color indicator auto switch is adjusted to show green at the stroke end, the indication may turn red when the cylinder returns by the backlash. This, however, is not an error.
196.5 300 369 L1 77 115.5 154 231 346.5 269.5 192.5 308 385 VV2CW3 L2 89 127.5 166 243 358.5 281.5 204.5 320 397 L3 101 139.5 178 255 370.5 293.5 216.5 332 409 L1 83 124.5 166 249 373.5 290.5 207.5 332 415 VV2CW4 L2 95 136.5 178 261 385.5 302.5 219.5 344 427 L3 107 148.5 190 273 397.5 314.5 231.5 356 439 Manifold composition 2stns. x 1 3stns. x 1 2stns. x 2 3stns. x 2 3stns. x 3 2stns. x
VX2 24 VDC GDM2A-G-S5 100 VAC VXK 110 VAC 200 VAC VXD None 220 VAC GDM2A-R 230 VAC VXZ 240 VAC 24 VAC VXS VXS 48 VAC 24 VDC GDM2A-G-Z5 100 VAC GDM2A-R-L1 110 VAC GDM2A-R-L1 200 VAC GDM2A-R-L2 220 VAC GDM2A-R-L2 230 VAC GDM2A-R-L2 240 VAC GDM2A-R-L2 24 VAC GDM2A-R-L5 48 VAC GDM2A-R-L5 VXB VXE With light VXP VXR VXH VXF Gasket Part No. for DIN Connector VCW20-1-29-1-F VX3 VXA Bracket Assembly
Single acting Normally open Normally closed Option Finger material Carbon steel (Standard), Stainless steel Dust cover material Chloroprene rubber (CR) (Standard), Fluoro rubber (FKM), Silicon rubber (Si) Model Series MHK2/Standard Type Width at closing (mm) L1 Width at opening (mm) L2 Note) Opening/Closing stroke (mm) L2L1 Max. operating frequency (c.p.m) Mass (g) Effective gripping force
Enter the asterisk at the beginning of individual cmponent part numbers.
(Value at the initial state) Impact resistance Conditions when tested with a drop tester in the axial direction and at a right angle to the armature, one time each in energized and deenergized states. No malfunction occurred when tested.
L Dimension L1 = 31n + 29, L2 = 31n + 14 n: Station 2 91 76 3 122 107 4 153 138 5 184 169 6 215 200 7 246 231 8 277 262 n Symbol L1 L2 853 VEX13 Series 0 3 Precautions Be sure to read this before handling the products. Refer to back page 50 for Safety Instructions and pages 387 to 391 for Precautions on every series. Operating Fluid Caution 1.
Dynamic moment MG Va Calculation Example CX m Operating Conditions Cylinder: CYP32 Mounting: Horizontal wall mounting Maximum speed: U = 300 [mm/s] Load mass: m = 1 [kg] (excluding mass of arm section) L1 = 50 [mm] L2 = 50 [mm] D-X L2 L1 20Data Item Load factor n Note 1. Maximum load mass m 1 = m/mmax = 1/5 = 0.20 L2 Review m. L1 M2 = m g (L1 + B) 103 2.
= 50 [mm] D-X L2 L1 20Data Item Load factor n Note 1.
(Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 2000 Hz. Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature.
(Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 2000 Hz. Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature.
(Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 1000 Hz. Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature.