PSxx-OMU0002CN kPa ZSE20AF5.0 kPa 1.5 ms OUT1 ON OUT1 OFF -28No.PS-OMU0002CN-D [F 2] OUT2 34 [F 1] OUT1 [F 3] 36 0 ms [F 4] 37 [F 5] FUNC 39 [F 6] 41 0% [F10] 42 std() [F11] 48 1000 [F80] 49 OFF [F81] 50 OFF [F82] 52 A [F90] 53 OFF [F96] 55 [F97] 56 OFF [F98] 58 () [F99] 60 OFF XY "---" -29No.PS-OMU0002CN-D [F 0] (kPa/MPa) <> [F 0] [F 0] ZSE20AF ZSE20A ISE20A MPa 0.001 0.001 0.001
moment of inertia [kgm2] Allowable moment of inertia [kgm2] 102 102 MK 103 103 50, 63 Standard arm single unit 32, 40 Standard arm single unit 104 50 100 200 104 50 100 200 Maximum piston speed [mm/s] Maximum piston speed [mm/s] 386 Model Selection MK Series Note) Maximum piston speed is equivalent to approximately 1.6x the average piston speed.
Controller version (the time in the bracket indicates the schedule for switching) Function Ver 2.0 Ver2.1 to Ver2.4 Ver2.5 (August 2014) (Sept. 2015) (June 2020) Corresponding card motor 6 types LAT3M-50 LAT3M-50 LAT3F-50 LAT3F-50 Alarm history count 4 points 4 points 20 points Communication speed 19200bps 2,400bps 2,400bps 9,600bps 9,600bps 19,200bps 19,200bps 38,400bps 38,400bps 57,600bps
Note) One of Nil, F or N is entered as thread symbol.
Refer to back page 50 for Safety Instructions and pages 543 to 546 for Flow Control Equipment Precautions. Piping Threads with Sealant Caution Mounting Caution AS-F AS-F 1. This product has a stopper for fully close in rotating direction. Excess torque may break the stopper. Table below shows the maximum allowable torque of the knob. 1.
E 2 x H A B C D Side support B MY-SB 2 x J A B C D A 61 70 87 B 75 84 105 C D E F G H J Part no.
F_Source/Destination_Address (F-Address) F-Source F-destination F-Address F-Address F_WD_Time F_WD_Time PROFIsafe ms F_SIL SIL F_iPar_CRC i-Prameters F_Par_CRC F-Parameters CRCF-Parameters F-CPU Failsafe controller, safe controller F_Destination_Address F-Parameter (F-Parameter) F-I/O device Failsafe I/O I/O 100 No.EX##-OMY0006CN F-Slave Failsafe slave F_Source_Address F-Parameter
Table displacement due to pitch moment load Displacement at "A" when load is applied at "F" Table displacement due to yaw moment load Displacement at "A" when load is applied at "F" Table displacement due to roll moment load Displacement at "A" when load is applied at "F" A A F F A F L L L 6 6 6 L = 80mm L = 80mm L = 80mm MXP 6-5 MXPJ6-5 MXP 6-10 MXPJ6-10 MXP 6-5 MXPJ6-5 MXP 6-10 MXPJ6-10
Yes Note) None Note) Yes Yes (W/o indicator light) Yes (W/o indicator light) Note) Note) Coil voltage Note) 1 2 3 4 5 6 9 100 VAC (50/60 Hz) 200 VAC (50/60 Hz) 110 VAC (50/60 Hz) 220 VAC (50/60 Hz) 24 VDC 12 VDC Note) DIN is applicable to VQZ2000/3000. Bracket Assembly Note) Part no.
() () ISA3-G () () ISA3-H ON OFF () () ON() OFF() -44No.PS-OMR0001CN-J 4 (1)(100 kPa200 kPa) (2) () (1) (2) 1 () (3) -45No.PS-OMR0001CN-J 4 2 [F 0] [F] 2 2 [][] 2 F 0(Unit) [ PA] kPa 47 ISA3-F[ 20] ISA3-G[ 50] ISA3-H[ 50] F 1(oUt1) OUT1 48 ISA3-F[ 3] ISA3-G[ 20] ISA3-H[ 20] [ SoG] ON OFF F 2(oUt2) () [ ---] 50 F 6( FSt) [ 0.0] 0.0 51 F10( SUb) [ LEvEL] 52 F80
Operating pressure: 0.4 MPa Model Selection Illustration When gripping a workpiece as in the figure to the left and with the following definitions, F: Gripping force (N) : Coefficient of friction between attachments and workpiece m: Workpiece mass (kg) g: Gravitational acceleration (= 9.8 m/s2) mg: Workpiece weight (N) F F the conditions under which the workpiece will not drop are mg F F
Operating pressure: 0.4 MPa Model Selection Illustration When gripping a workpiece as in the figure to the left and with the following definitions, F: Gripping force (N) : Coefficient of friction between attachments and workpiece m: Workpiece mass (kg) g: Gravitational acceleration (= 9.8 m/s2) mg: Workpiece weight (N) F F the conditions under which the workpiece will not drop are mg F F
(mm) Electrical entry P Port size B C D E F H K L M N A Grommet: G Conduit: C Conduit terminat: T Model Q R Q R Q R S U 13.5 28 64 31 6.5 12.5 28 14 12.8 M4 4.5 22 59 44 50 99 50 66 83 1/8 VCS21 18 36 67.5 31 8.5 12.5 28 18 12.8 M4 6 22 62 44 53 99 53 66 86 1/4 22 40 81.5 36.5 11 15 32 20 19 M5 8 24 76 46 66.5 101 66.5 68 99 1/4, 3/8 VCS31 30 50 86 36.5 13.5 15 32 25 23 M5 8 24 80 46 71 101
Deflection + L F F (Dimension when extended) + M Built-in coil scraper and Lube-retainer MAllowable lateral load graph MSelectable proximity switches CKZP57L TURCK P&F 400 Allowable lateral load [N] 350 300 250 200 MAdjustable connector angle 150 100 CKZP57L: 45, 90 CKZP71: 0, 45, 90 50 0 0 50 100 150 200 250 Offset distance L [mm] CKZP71 0 50 100 150 200 250 300 350 400 450 500
[F 2] OUT2 OUT1 -43No.PF-OMO0004CN-E [F 3] <> [F 3] [F 3][rES] [rES][] [F 3] -44No.PF-OMO0004CN-E [F10] <> [F10] [F10][FLo] [FLo][] [F10] 3) 9 L(9.9 ft 3 3 3 50 L 60,008 L 203,481,019 L (57 ) (47 ) ((49 )) -45No.PF-OMO0004CN-E [F13] ON <> [F13] [F13][rEv] [rEv][] ON OFF() ON() [F13] -46No.PF-OMO0004CN-E [F20] [---] =00 = ONEEPROM 100+100 OFF <> [F20] [F20]
Refer to back page 50 for Safety Instructions and pages 543 to 546 for Flow Control Equipment Precautions. Design and Selection Mounting Warning 1. Check the specifications. Warning AS-F AS-F 3. Tighten threads with the proper tightening torque. TMH The products in this catalog are designed to be used in compressed air systems (including vacuum) only.
M2 m2 M3 m3 25 32 40 23 26 23 27.5 27.5 27.5 MY1H 39 50 39 39.2 39.2 39.2 50 50 39 50 50 50 The above values are the maximum allowable values for moment and load mass.
(Value in the initial state) VA Body ported SA Series SYJA500 VA With Bracket VM VR Air operated valve type SYJA5 2-M5-F, SYJA7 2-01-F 1 2 1 2 Note) Bracket is not mounted.