Mechanically jointed rodless cylinder Basic short type (Rubber bumper), Basic standard type (Air cushion) Slide bearing guide type (Air cushion) Do not use compressed air that contains chemicals, synthetic oils including organic solvents, salts or corrosive gases etc., as this can cause damage or malfunction. -5- Caution 1. Install an air filter. Install an air filter upstream near the valve. Select an air filter with a filtration size of 5m or smaller. 2. Install an aftercooler, air dryer, or water separator before the filter.
Note 5) For command pulse input with an open collector method.
Caution 2. Humidity of ambient environment When using the valve in environments with low humidity, take measures to prevent static. If the humidity rises, take measures to prevent the adhesion of water droplets on the valve. 2. Install an air filter. Install an air filter upstream near the valve.
(Tightening torque: 0.6Nm) SW3 SW2 SW1 Address 1 2 0 0 0 0 1 1 0 0 2 2 N.C. 9 9 99 0 0 100 0 1 101 1 2 5 125 Bus terminator switch ( SW4 ) This switch can set the bus terminator. -19No.EX##-OMO0019 Configuration In order to configure the GW unit in the PROFIBUS DP network, the appropriate device master file (GSD file) for the GW unit will be required.
Install an air filter. Install an air filter upstream near the valve. Select an air filter with a filtration size of 5m or smaller. 2. Install an aftercooler, air dryer or drain catch before the filter. Compressed air that contains excessive foreign material may cause malfunction of valves and other pneumatic equipment. 3. Discharge condensates regularly.
Lubrication Warning 2. Install an air filter. Install an air filter upstream near the valve. Select an air filter with a filtration size of 5 m or smaller. 1) The valve has been lubricated for life by the factory 3. Take measures to ensure air quality, and does not require any further. such as by installing an aftercooler, air dryer, or water separator.
1 pc. 5 *1 5 2 pcs. 10 *1 10 D-A9V 1 pc. 5 2 pcs. 10 D-Z7 D-Z80 1 pc. 5 *1 5 2 pcs. 10 D-Y59 D-Y7P 1 pc. 5 *1 5 2 pcs. 10 D-Y69 D-Y7PV 1 pc. 5 2 pcs. 5 D-Y7W D-Y7WV 1 pc. 5 *2 2 pcs. 10 *2 D-Y7BA 1 pc. 5 *2 2 pcs. 10 *2 D-P3DWA 1 pc. 15 2 pcs. 15 D-P4DW 1 pc. 5 *2, 3 2 pcs.
The valves listed in this manual are not designed for safety applications such as an emergency shutoff valve. If the valves are used for the mentioned applications, additional safety measures should be adopted. 4 VFR3000OMH0003B 5 VFR3000 Series 5 Port Solenoid Valve / Precautions 2 Be sure to read before handling. 6. Operation for air blowing Design / Selection 2.
Note 2) Set the pressure within operating pressure range of solenoid valve. Note 3) Solenoid valve: Max. 50C. Note 4) Synthesized effective area with 2 position. Note 5) Operate an interface regulator only by applying pressure from the P port of the base, except when using it as a reverse pressure valve.
B-1 A-1 B-2 A-2 B-3 A-3 Signal Cable color S Brown Red Orange Y ellow Green Blue A A B B COM-A/COM COM-B/ 2 1 6 5 3 4 Cable color Connector D terminal no.
The figures in the above table indicate stationary current. 2. An inductive load has a power factor (AC) of 0.75 or more, and a time constant (DC) of 7 msec or less. 3. A light load has an inrush current 10 times greater. 4. Lead wires are connected using a soldering terminal. 5. The electrical entry is equipped with a conduit (G1/2) and grommet. 6.
Connections 1/2 inch face seal 1/2 inch tube weld 0.21 30 3.
Specific service None. -23No.EX-OMN0013-I 5. DeviceNet Connection Object (Class ID: 05h) 5-1. Class attribute ID Access rule Description Value 5-2. Class common service Service code Description 5-3.
When installing an ionizer with Auto balance sensor [body-mounting type] in proximity with an ionizer which operates in DC mode, they should be positioned at least 2m away from each other. When using an Auto balance sensor [body-mounting type] near an ionizer in DC mode, keep clearance of at least 2 m between them.
PPS Product 460 g 5 520 g 5 700 g 5 1150 g Weight Lead wire and connector 100 g 1: Refer to the measurable range chart for ethylene glycol aqueous solution (page 38). 2: If the flow rate is smaller than the minimum flow of the display range, 0 L/min. will be displayed. 3: Selectable by setting. 4: The material is FKM for product with operating fluid temperature specification [0 to 90 oC].
unit DIN rail 8-M3 3 x 7.2 ( = 21.6) 36 2-3.4 6.4 15 1 2 3 4 6.5 26 FLOW SWITCH SMC 35.5 m30 56 (4.5) 44 UNIT RESET SET 5 6 7 8 29 38 15.2 7 Series PFA Digital Flow Switch for Air Dimensions (mm)/ Separate Type For Air 1in=25.4mm Scale: 70 % PFA5 0-m m (N) 1 5 Sensor Unit 98 56 82 60 42 6 17 1.6 48.2 34 54 44 24 2-Piping port size 4-4.5 40 50 (43.5) 42 2 1 4 3 4 Connector pin numbers 43
Refer to Best Pneumatics No. 2-1 for details. 361 CH2E/CH2F/CH2G/CH2H Series Construction @7 q y i @8 !4 #1 @6 @1 u @0 #0 o w !5 !8 !9 !6 !7 @9 !2 @2 @4 t e !0 CH2G Series !3 @3 r @5 !
The filtration degree should be 5 m or finer. 2. Install an air dryer, after-cooler or water separator, etc. Air that includes excessive drainage may cause malfunction of valves and other pneumatic equipment. To prevent this, install an air dryer, after-cooler or water separator, etc. 3. Use the product within the specified range of fluid and ambient temperature.
Use an air filter with 5 m or less filtration rating on the inlet side of the valve to avoid any damage to the seat caused by dust when mounting a 3 port valve for residual pressure release on the inlet side. 5 Series ACG20/30/40 Dimensions ACG20 Standard Downward facing handle ACG30/40 Standard Downward facing handle A F E P G 2-L A F E 2-L G P B C H2 H1 OUT IN C B H2 H1 OUT IN SMC 2-L SMC