VCC Fluids that solidify or being cured may block the leak detection so port and leak may not be detected. 2. If applying high voltage to the fluid, it must be earthed by using the bolt to mount the base. Do not use sealing tape when piping, as it may insulate. e If the union nut is loose, tighten it by hand temporarily.
If cleaning the rotating part, grease may leak out, which shortens product service life. Thus, cleaning must be as infrequent as possible. 2. If excess water gets into mounting holes, unwanted bacteria may reproduce. Plug them with plug bolts or external covers to avoid this.
WARNING If parameter Pn600 is set to 0 while an external Regenerative resistor is connected, the regenerative overload alarm (A.320) may not be detected. If the regenerative overload alarm (A.320) is not detected correctly, the external Regenerative resistor may be damaged and an injury or fire may result.
Note 4: When short period power shortage (including instantly recovered shortage) is recovered, it may take a longer starting period than usual starting or may not start due to the protective devices.
WARNING WARNING indicates that there is a hazard that may cause serious injury or death if not avoided. CAUTION CAUTION indicates that there is a hazard that may cause minor injury.
WARNING WARNING indicates that there is a hazard that may cause serious injury or death if not avoided.
Incorrect handling of the product may cause breakage or operation failure of the equipment or device. 3) Do not touch the product when operating at high temperature (40 to 60oC). The operators may get burnt.
Incorrect handling of the product may cause breakage or operation failure of the equipment or device. (3) Do not touch the product when operating at high temperature (40 to 60oC). The operators may get burnt.
It may cause malfunction. (3) The product should not be exposed to prolonged sunlight.
Setting of display resolution may not be available depending on the units for display.
(Single solenoid, 3 position: 0.2 to 0.9 MPa, Double solenoid: 0.1 to 0.9 MPa) If no improvement is achieced in spite of the above countermeasure, inside of the valve may have some abnomality. In this case, stop using the balbe immediately If any of followings are carried out, inside of the valve may have some failure.
If excessive carbon dust is generated by the compressor, it may adhere to the inside of a valve and cause it to malfunction. For compressed air quality, refer to the SMC Best Pneumatics catalog No. 6. 2. Lubrication amount Operating Environment If too much oil is applied, it may accumulate inside the valve, causing malfunction or response delay.
The switch may be damaged if a screw other than the one supplied, is used.
(Without a release valve, the work piece may not be released.)
If the flow rate of the supply valve is insufficient, it may lead to vacuum failure.
The use of turbine oil as a fluid for an air cylinder may result in oil leakage. 4. The oil stuck to the cylinder is grease. 5. The base oil of the grease may seep out.
If the operation is restarted within five minutes, the protection circuit may activate and the operation may not start properly. 2. Operation and suspension frequency should not exceed 10 times per day. Frequently switching between operation and suspension may result in the malfunction of the refrigeration circuit.
It may cause malfunction of locking and release. If mounting is done with lock engaged, lock mechanism may be damaged. C95 r Use with load 50% or less of rated capacity. CP95 Rubber cover If cylinder is used at 50% load capacity or more, lock may be damaged. NCM t Do not use two cylinders in parallel at same time.
It may also result in non-conformity to safety standards. Product handling Installation Do not drop, hit or apply excessive shock to the fieldbus system. Otherwise damage to the product can result, causing malfunction. Tighten to the specified tightening torque. If the tightening torque is exceeded the mounting screws may be broken.
If the tightening torque is exceeded the mounting screws and brackets may damaged. If the tightening torque is insufficient, the product may be displaced and the mounting screws may come loose (Refer to page 14 Mounting and Installation.) Ensure that the FG terminal is connected to ground when using a commercially available switch-mode power supply.