4-channel Flow Monitor (Remote type monitor unit) The output condition is also basically recovered to that before a power cut or de-energizing, but may change depending on the operating environment.
If the pump is operated for a long time without any fluid inside, the diaphragm may be damaged or the life may be shortened. Do not continue idling longer than 3 minutes. (11)Pilot port condensation and freezing Condensation may form in the piping of the AIR SUP port, due to sudden cooling because of the expansion of supply air. The fluid may freeze in winter.
Therefore, it should be noted that the described characteristic values may vary depending on the loop conditions. OUT(+) 5: (ANR) shows standard air in accordance with JIS B0120. 6: The visibility of LCD display may be reduced at lower E Main temperature.
If the SI unit is not assembled properly, inside PCBs may be damaged or liquid and/or dust may enter into the unit.
Jul.26.2006 6.1: Change Accuracy related to temp(stability) 1.2 Add HEC006-A May.20.2008 1.3 Add caution of the heavy object.
AD27-A with auto drain may leak during exhaust of pressure. (This leakage is allowed in their constructions and not failure.) Be sure to connect piping for drain. Selection WARNING Fluorine grease and Mineral grease used on internal surfaces and packing may leak to the outlet. Please contact SMC if this is a problem.
Under tightening may result in loosening or sealing failure while over tightening may cause damage to threads and other problems. Caution 1. Once a lubricant is introduced, be sure to continue lubrication. If it is discontinued, malfunction may result due to loss of the initial lubricant. Apply class 1 turbine oil (ISO VG32) as a lubricant. Use of other lubricants may cause malfunction.
There is a possibility that the lock may not be released. (Refer to Lock Release.) 3. Release the lock when mounting or adjusting the cylinder. If mounting or other work is performed when the cylinder is locked, the lock unit may be damaged. 4. Operate at 50% or less of the theoretical output.
(Tube may release due to pressure pulsation or water hammer effect.) 7. If using a fluoro-resin tube in an environment where the fluid temperature changes drastically, it is recommended to use an inner sleeve. Otherwise, air leakage may occur or the tube may release from fitting due to deformation of the tube.
If the torque limit is canceled during servo lock, the servo motor may suddenly rotate according to position deviation with respect to the command position. In general make the connections shown below.
WARNING If parameter Pn600 is set to 0 while an external Regenerative resistor is connected, the regenerative overload alarm (A.320) may not be detected. If the regenerative overload alarm (A.320) is not detected correctly, the external Regenerative resistor may be damaged and an injury or fire may result.
If the cooling water in a cooling tower is used, the water quality standard will be satisfied at the initial stage, however, if it is used in an air contaminated environment, sulfurous acid gas in the air may dissolve into the cooling water, forming sulfuric acid which may corrode the electro-thermal surface.
If the cooling water in a cooling tower is used, the water quality standard will be satisfied at the initial stage, however, if it is used in an air contaminated environment, sulfurous acid gas in the air may dissolve into the cooling water, forming sulfuric acid which may corrode the electro-thermal surface.
WARNING WARNING indicates that there is a hazard that may cause serious injury or death if not avoided. CAUTION CAUTION indicates that there is a hazard that may cause minor injury.
Any port may be pressurized, back,pressured. or plugged without affecting spoot action. ANSt symbot shows the vatve a6 a slngle inl6t as a single intl 4-way, but vatve may be us6d, wilhout modtfication, as a dual Inlel 4-way, a O-way, or a 2.way, by ptping and/or ptugging the appropriale ports. MOUNTING: Intended for sub.ptate or manitotd mounting. May be mounted In anv Dosi. lion.
As a result, the tensile compression force of the floating joint may exceed its maximum level. 2. The dust cover may adhere to the stud.
Speed controller can be used to control the speed of multiple cylinders simultaneously for a short period of time, but depending on conditions, it may not work as desired. If multiple cylinders cannot operate simultaneously, unreasonable force is applied to the piston rod because cylinder positions may not be the same.
The auto switch may be damaged if a screw other than the one supplied is used.
Otherwise, a malfunction may occur.
The following procedures are an example of how a test may be performed. It is intended as an overview and not as an all inclusive description. 1) Rotate the adjustment wheel counterclockwise (DECR) completely to relieve spring force.