48 If the space is not sufficient, the magnets in adjacent cylinders may cause the auto switches to malfunction.
If using other screws, switch may be damaged.
The lock may be released due to inflow of the unlocking pressure. 2. Install speed controllers for meter-out control. Malfunction may occur if meter-in control is used. 3. Be careful of reverse exhaust pressure flow from a common exhaust type valve manifold.
If the tightening torque is exceeded the mounting screws may be broken. IP67 protection cannot be guaranteed if the screws are not tightened to the specified torque. If a large manifold valve is mounted, lift the unit so that stress is not applied to the connecting part while transporting. The stress may cause breakage of the connecting part.
If the tightening torque is exceeded the mounting screws may be broken. IP67 protection cannot be guaranteed if the screws are not tightened to the specified torque. If a large manifold valve is mounted, lift the unit so that stress is not applied to the connecting part while transporting. The stress may cause breakage of the connecting part.
The product specified here may become unsafe if handled incorrectly.
If the SI unit is not assembled properly, inside PCBs may be damaged or liquid and/or dust may enter into the unit.
It may also result in non-conformity to safety standards. -5No.EX-OMB0014-H Product handling Installation Do not drop, hit or apply excessive shock to the fieldbus system. Otherwise damage to the product can result, causing malfunction. Tighten to the specified tightening torque. If the tightening torque is exceeded the mounting screws may be broken.
The fittings may be damaged. 6. The valve cannot be used if there are fluctuations of the load. The piston rod may jerk during operation. 7. In case a closed-center solenoid valve is used, switch to the center position only after pressure charge inside the cylinder at the stroke end is completed. If the pressure charge is insufficient, the piston rod may jerk after restart.
If an excessive force is applied on the connector in the LOCK position, the connector block may be damaged. Also, using in such a way that the connector floats in the FREE position, it may cause the lead wire, etc. to break. Thus, refrain from using in these ways.
One of the following may have occurred. (DeviceStatus : Failure) Valve has a short circuit. Pressure sensor has a short circuit. Pressure sensor has a failure or a disconnection. No connection or a disconnection between the SI Unit and vacuum manifold. There is a firmware error. Red ON ST One of the following may have occurred.
Note 4: When short period power shortage (including instantly recovered shortage) is recovered, it may take a longer starting period than usual starting or may not start due to the protective devices. 6-2 Refrigerant with GWP reference Note1:This product is hermetically sealed and contains fluorinated greenhouse gases. Note2:See specification table for refrigerant used in the product.
Vibration of Y or Z axis may occur depending on the operating pattern. In such cases, take measures such as installation of a support guide. A regenerative absorption unit may be necessary depending on the operating conditions. Pay careful consideration to this issue. The gain adjustment and wiring must be conducted by the customer.
The warranty period of the product is 1 year in service or 1.5 years after the product is delivered.2) Also, the product may have specified durability, running distance or replacement parts. Please consult your nearest sales branch. 2.
Speed controller can be used to control the speed of multiple cylinders simultaneously for a short period of time, but depending on conditions, it may not work as desired. If multiple cylinders cannot operate simultaneously, unreasonable force is applied to the piston rod because cylinder positions may not be the same.
If the space is not sufficient, the magnets in adjacent cylinders may cause the auto switches to malfunction.
Note 3) The number of stations that may be displayed is longer than the manifold number of stations.
When the handle is rotated with a tool, it may apply excessive torque to the handle or inside the valve body and it may cause damage. Rotate the handle by hand. 9. When locking the valve with LOTO feature in the closed position, use safety lockout hasp. (AP3657, AP4657, AP3157, AP3900) The valve with LOTO feature has a built in LOTO capability.
Note 3) The number of stations that may be displayed is longer than the manifold number of stations.
Furthermore, abnormal temperature rise caused by adiabatic compression may result in the tube bursting. Note 2) Do not use this product in a manner in which the tube is not fixed. Observe the lesser value of the maximum operating pressure between the tube and fitting. A material change over a long duration or due to high-temperature may cause leakage.