VQ4000 PUSH Terminal block marking Model A COM B T TURN 0 1 0 1 VQ410 A side COM LOCK VQ420 Caution A side COM B side 3 4 5 6 0 1 VQ4 0 A side COM B side Valve Mounting After confirming the gasket is correctly placed under the valve, tighten the mounting screws with the appropriate torque listed below. Note 1) Not polar, possible to use as COM.
LEC-OM08003 // LEC-T1 Series LEC6 LECPA TB Ver2.1 .5 .7 1. .9 1.1 .9 1.9 2.10 1.2 .11 1.11 2. .12 3. .13 3.1 .13 (1).13 (2)Tree .13 3. .14 (1).14 (2)Tree .15 4.16 5. .17 5.1 .18 5.2 .19 (1).19 (2).19 5.3 .20 (1).21 (1-1) LECPLECA 22 (2) .23 (2-1) LECPLECA 23 (2-1-a) TB Ver1.**. 23 (2-1-b) TB Ver2.**. 25 (2-2) LECPLECA 27 (2-2-a) TB Ver1.**. 27 (2-2-b) TB Ver2.**. 29 (2-3) LECPLECA .32 1
(Part 1: General requirements) ISO 10218: Manipulating industrial robots -Safety. etc. Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury.
Recommended Connection Thread Tightening Method Caution (1) Fittings with sealant: R a) First, tighten the fitting by hand, then use a wrench appropriate for the hexagon flats of the body to tighten it a further two or three turns. For a tightening torque guide, see the table below.
Plate A Plug (M-3P) (2 pcs.) Plate B (with O-ring) Tighten by hand and give it an additional turn approx. 1/4 rotations with a wrench.
For example, when analogue output is 1 to 5 V, F.S. = 5[V] 1[V] = 4[V], (ref. 1%F.S. = 4[V]x1% = 0.04[V]) The maximum measuring range or change in analogue output over the maximum measurement range. F.S. (Full span, Full scale) K When an object is placed in a fluid stream, a vortex will be created in the fluid on the downstream side. This vortex is called a Karman vortex.
(mm) 4 6 8 10 12 (1) AS221FE-01 AS231FE-01 20, 25, 32 R 1/8 AS221FE-02 AS231FE-02 20, 25, 32, 40 R 1/4 AS321FE-03 AS331FE-03 40, 50, 63 R 3/8 AS421FE-04 AS431FE-04 63, 80, 100 R 1/2 Note 1) Elbow type only Note 2) Distinction between meter-out/meter-in types by appearance Those are distinguished by the lock nut.
PVC PVC PVC PVC PVC , -10No.PF-OMM0004-D -11No.PF-OMM0004-D N M8 M8 R / ZS-40-K PF3W704/720 4 3X8 ZS-40-L PF3W740 4 3X8 ZS-40-M PF3W711 4 4X10 M8 ZS-40-A 3 m 2 250 L/min PVC 25 A ZS-40-U25 25 A PVC 1 PVC 30 A ZS-40-U30 30 A PVC 1 25 A ZS-40-U25-A 1 M5x80 2 30 A ZS-40-U30-A 1 M5x65 2 PVC 1~2% -12No.PF-OMM0004-D 1 DC+ 2 OUT2 3 DC4 OUT1 M8 IN OUT OUT1OUT2 ON UP ON/OFF SET
Warning 1/8 35 3/8 1520 1/2 2025 3/4 2830 1 3638 1 1/4 4042 1 1/2 4850 2 4850 Follow the procedure of the manufacturer when fittings other than SMC is used. 1) If the fitting is tightened with excessive torque, a large amount of sealant will seep out.
Prior to using SMC products, please read and understand the warranty terms and disclaimers noted in the specified catalog for the particular products. *1) Vacuum pads are excluded from this 1 year warranty. A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
Selection conditions Mounting: Vertical Maximum speed: 500 mm/s Overhang L: 40 mm Load mass m: 0.1 kg 1 Mass m (kg) 20 16 10 0.1 6 Refer to Graph c based on vertical mounting and a speed of 500 mm/s. In Graph c, find the intersection of a 40 mm overhang L and load mass m of 0.1 kg, which results in a determination of 16.
Port for extending cylinder Port for retracting cylinder Rc 1/8 relief port 3 Guide Table Series MGF Construction @2 !2 y u !3 e q t r o w @0 !1 !7 !8 !9 !5 !6 !0 i @4 @1 !4 @3 @3 When the cylinder is extended When the cylinder is retracted Description Material Note Parts list Description Material Note Parts list No. No.
Specific Product Precautions (4) (1) Fittings with sealant: R 1) First, tighten the fitting by hand, then use a wrench appropriate for the hexagon flats of the body to tighten it a further two or three turns. For a tightening torque guide, see the table below.
Do not use a V-band which is deformed or with a damaged thread. (See page 7 table 1: V-band for replacement) 6. Prepare a drain for the circuit to discharge fluid where necessary. 7. Use the filter with a circuit in which the changing load of pressure and flow is small. 8.
Note 1) Avoid using in a vacuum holding application such as a leak tester, since there is leakage.
Symbol How to Order 2 1 01 06 2 AS 1 F E S K JIS Symbol Hexagonal lock nut Body size 2 3 4 1/8, 1/4 standard 3/8 standard 1/2 standard With seal Applicable tubing O.D. (mm) 04 06 08 10 12 Type 4 6 8 10 12 Port size Elbow Universal 2 3 01 02 03 04 R 1/8 R 1/4 R 3/8 R 1/2 Control type Meter-out Meter-in 0 1 With residual pressure release valve With One-touch fitting 15-9-36
the HF2-BF* series, we recommend that you install a dryer (IDF, IDG, ID), a line filter (AFF-D series), a mist separator (AM series), a micro mist separator (AMD series), a super mist separator (AME series), an odor removal filter (AMF series), and an active carbon filter (AMK series). 3) Use a grade that meets ISO8573-1: 2010 [1: 4: 1] for the compressed air purity classes on the inlet
IR-OM00015 PRODUCT NAME Precision Regulator MODEL / Series / Product Number IR300(0, 1, 2)-A IR301(0, 1, 2)-A IR302(0, 1, 2)-A Contents Safety Instructions 2 to 6 1. Application 7 2. Specifications 7 3. Construction and Operation Principles 8 4. How to order 9 5. Bracket, gauge and switch assembly (optional) 10 6. Panel mounting 11 7. Troubleshooting 12 8.
A large amount of dust may 1 (No indication on (0.1C) 25.0 Do not touch the surface when the set temperature is high.
It is also possible to manufacture a bidirectional lock-up cylinder. For details, refer to Made to Order on page 9-6-113. Due to the nature of its construction, a lock-up cylinder has a play of approximately 0.5 mm to 1 mm in the axial direction.