1

VM SUP blocking disk assembly SY30M-40-2A SY50M-40-1A SY70M-40-1A EXH blocking disk assembly Series SY3000 SY5000 SY7000 SY30M-40-1A SY50M-40-1A SY70M-40-1A XT34 Label for blocking disk If the blocking disk assembly is ordered using the manifold specification sheet and ordered at the same time as the manifold, the position where the blocking disk assembly is inserted will be labeled and

2

(C) Correction factor 1.25 1.11 1 0.90 0.63 2 to 25 30 32 35 40 2 to 25 30 32 35 40 45 2 to 25 30 32 35 40 2 to 25 30 32 35 40 2 to 25 30 32 35 40 Note) For the water-cooled type, the correction factor is determined to 1 in an ambient temperature range of 2 to 45C.

Table of Contents

bearing CY1S6 to 40 !

Table of Contents

x 1.5 Up to 700 1/8 146 9 10 40 40 60 196 206 20 42.5 40 32 M26 x 1.5 Up to 1000 1/8 159 9 10 40 60 209 219 22 40 51 M32 x 2 53 Up to 1000 1/4 181 10 11 53 77 236.5 247 26.5 The dimension NA(42.5) is wider than dimension TX(40).

Table of Contents

In the graph, find where the lines representing a load weight of 40 kg and an eccentric distance of 80 mm intersect.

Air Slide Table

40 40 40 40 40 Stroke 50 50 50 50 50 50 75 75 75 75 75 100 100 100 100 125 125 125 Page 11 150 150 Low thrust with high rigidity type MXQB 10 10 10 10 10 20 20 20 20 20 30 30 30 30 30 40 40 40 40 40 Stroke 50 50 50 50 50 75 75 75 75 75 100 100 100 100 125 125 125 Page 53 150 150 Single side-ported type MXQC 10 10 20 20 30 30 Stroke 40 40 50 50 75 75 Page 67 100 Height interchangeable type

ZP

50 +25 +25 +40 +49.9 +51.4 +40 + 9.9 +51.4 13-11-110 New New Vacuum Pad More shapes and sizes of pads.

Table of Contents

(Refer to page 13-2-40 for How to Order.) Combination Symbol: K2 Combination Symbol: K7 An N.C. solenoid valve is used as the supply valve. Also, an external 2 port valve (vacuum valve) must be provided to serve as the vacuum release valve. An air operated N.O. valve is used as the supply valve. An N.C. solenoid valve is used for the vacuum release valve.

ZP

Male thread Female thread 40 40 6 tube 06 50 50 8 tube 08 M5 x 0.8 A5 Pad type (Refer to Table (1) for applications.)

Table of Contents

If the workpiece gripping point goes beyond the range limits, this will have an adverse effect on the life of the air gripper. 0.7 MPa 0.6 MPa, 0.7 MPa 0.6 MPa, 0.7 MPa 0.3 MPa 0.3 MPa 40 20 0.4 MPa 0.4 MPa 0.5 MPa 0.5 MPa 20 10 0 10 20 30 40 50 0 20 40 60 80 100 Gripping point L (mm) Gripping point L (mm) MHZ2-40 MHZ2-16/11-MHZ2-16 120 Pressure 0.2 MPa Pressure 0.2 MPa 60 0.6 MPa 0.6 MPa

Electric Actuator/Slider Type

16 6 40 46 25 9.5 48 57.5 32 16 63 79 40 0 68 68 Step motor, Stroke: 300 mm Step motor Top surface of table and motor are level.

CY1

0 60 80 20 40 0 60 20 40 0 60 Moment ( Nm) Moment ( Nm) Moment ( Nm) Intermediate Stops Vertical operation 1) Intermediate stopping of load with an external stopper, etc.

Table of Contents

A cabtire cable with an O.D. 6 to 12 mm is applicable. Tighten each part with an appropriate tightening torque shown below.

Table of Contents

40 50 50 55 55 65 85 , Misc.

Magnetically Coupled Rodless Cylinder Series CY3 B R /CY1 1

bearing CY1S6 to 40 !