Compact Cylinder Standard Strokes Bore size [mm] Standard stroke [mm] 12, 16 5, 10, 15, 20, 25, 30 20, 25, 32, 40 5, 10, 15, 20, 25, 30, 35, 40, 45, 50 50, 63, 80, 100 10, 15, 20, 25, 30, 35, 40, 45, 50 Intermediate strokes are available as a special order.
(Refer to 2.3.1 Setting of contact input signal type and form) If an input from an external switch is detected, it can be generated as an alarm.Options to select continuous monitoring or monitoring during operation are available. Also, the detection start time after the start of operation and the detection end time can be set.
(8.3-2O0OHz) o External Pilot Tape,/ NVJ300R An external pilot supply is required when main valve pressures are lower than 20 PSl.
(8.3-2O0OHz) o External Pilot Tape,/ NVJ300R An external pilot supply is required when main valve pressures are lower than 20 PSl.
(8.3-2O0OHz) o External Pilot Tape,/ NVJ300R An external pilot supply is required when main valve pressures are lower than 20 PSl.
CX Model Intermediate stroke Standard stroke (mm) Symbol Specifications As for the intermediate strokes (by the 5 stroke interval) other than the standard strokes at left are manufactured by means of installing a spacer with the width of 5, 10, 15, 20, 25 mm. Example) In the case an MGF63-15 specification is required, a spacer of 15 mm is installed in the MGF63-30.
Parts Purpose Connect to DeviceNet line with an accessory connector for DeviceNet ( ). 10 1 Communication socket (BUS) Input unit 1 connector 2 inputs type ( ) Supplying power for output instruments such as a solenoid valve with an accessory connector ( ). 11 2 Power supply socket (PWR(V)) Supplying power for controlling GW and for input instruments such as a sensor with an accessory connector
Install an air filter near this product on the supply side. Select a filtration degree of 5m or less. 2. Compressed air containing a large amount of drainage can cause malfunction of this product and other pneumatic equipment. As a countermeasure, install an after-cooler, air dryer or water separator, etc. 3.
Applicable model A B C D E F G H J L t AS-10D ZH05/07/10DA 11 18 3.5 3.4 18.2 23.2 45 6.2 11.2 14 1.6 AS-25D ZH13/15DA 17 25.8 4.4 4.5 22 27 20 AS-30D ZH18/20DA 22 30.8 27.2 32.2 22 231 ZH Series Circuit Examples Caution Handling of Circuits Select the related air preparation equipment with applicable size in reference to the circuit example below.
At the time of shipment from the factory, it is set such that the security code is not required. 10 Series PFMC Analog output free range function Allows the flow that generates an output of 5 V or 20 mA to be changed. The value can be changed 10% of maximum rated flow to maximum display value.
Lightning surge countermeasures should be applied directly to system components as necessary. 2. Our pressure switches do not have an explosion proof rating. Never use in the presence of an explosive gas as this may cause a serious explosion. 3. Do not use in an environment where static electricity can cause problems, otherwise system failure or malfunction may result. 1.
Be sure to connect the load to the rod end with the cylinder in an unlocked condition. If this is done when in a locked condition, it may cause damage to the lock mechanism. 1. Do not perform unlocking when an external force such as a load or spring force is being applied. This is very dangerous because the cylinder will move suddenly. Take the following steps. CL CL1 2.
This seat is available as an option for high temperature applications or specific gas applications, such as N2O or CO2. [PEEK] Polyetheretherketone. This material has excellent heat, fatigue and chemical resistances as thermoplastic resin. This seat is available as an option for the regulators. [Viton] Trademark of DuPont Fluoro-rubber (FKM).
This allows reading and monitoring the contact signal from an external switch. When inputting an external switch signal to the contact input, select External Switch (external switch signal) for the type of contact input signal. (Refer to 2.3.1 Setting of contact input signal type and form) If an input from an external switch is detected, it can be generated as an alarm.
Hole Switch holder B Switch holder A Switch guide Switch case Figure 2 Solid state switch First groove MRHQ 20, 25 D-F9 3. Secure the switch at an appropriate position with a flat head watchmakers screwdriver as indicated in Figure 3. Tightening torque: 0.05 to 0.1 Nm Second groove MRHQ 10, 16 3.
Never turn the connector as it is not designed to turn.
-150 JA63-16-200 JA80-20-250 JA100-24-300 JA100-27-150 JA125-27-200 JA160-33-200 20 25 32 32, 40 40 32, 40 50 50, 63 80 100 100 125 160 1100 2500 2500 4400 4400 4400 11000 11000 18000 28000 28000 28000 71000 13 17 17 22 22 22 27 27 32 41 41 41 55 7 8 8 11 11 11 13.5 13.5 16 20 20 20 24 7 8 8 11 11 11 14 14 19 24 24 24 36 4.5 5 5 6 6 6 7.5 7.5 9.5 11.5 11.5 13 16 21 24 24 31 31 31 41 41 50
Take measures to ensure air quality, such as by installing an aftercooler, air dryer, or water separator. Compressed air that contains a large amount of drainage can cause the malfunction of pneumatic equipment, such as magnet grippers. Therefore, take appropriate measures to ensure air quality, such as by providing an aftercooler, air dryer, or water separator. 40 - 4.
(Nil) CG3 CG3 Bore size G: Same rod end dimensions (A, AL, H) as CG1 series. 20 25 32 40 50 63 80 100 20 mm 25 mm 32 mm 40 mm 50 mm 63 mm 80 mm 100 mm JMB Number of auto switches Mounting brackets are shipped together, (but not assembled). MB AL Nil S n 2 pcs. 1 pc. n pcs.
For connection with a load having an external support/guide mechanism, select an appropriate connection method and perform careful alignment.