IN20267 Never mount a product in a location that will be used as a foothold. The product may be damaged if excessive force is applied by stepping or climbing onto it. Do not use this cylinder as a stopper. Minimum adjusting stroke necessary for a positioning stop is 5mm. Operate for 5mm or more before a positioning stop. Ex: 1.
Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.
For a facility having a small installation area (that can not vent the air naturally): Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level. 3.
When a surge-generating load, such as a relay or solenoid valve, is driven directly, use a product that incorporates a surge absorption element. 18. The power supplies should be separated between the controller power and the I/O signal power, and both power supplies must not be of the inrush-current limited type.
Since a large quantity of liquid will be pumped out, use a suitable throttle in the discharge port if problems occur. Note 3) With a low number of operating cycles, even a valve with a small Cv factor can be operated.
From a point indicating 500 mm/s on the axis of abscissas, extend a line upward and find a point where it intersects with a line for the 63 mm bore size. Extend a line from the intersection to the left and find a load mass 80 kg.
Do not use this product on board a vehicle or a vessel. This product must not be installed and used on board a conveyance such as a vehicle or a vessel, as it may become damaged due to vibration. If it must be used in such a manner due to unavoidable circumstances, please contact SMC beforehand. 1.
Consider selecting a ZNC series (body size 20) Bernoulli gripper as a substitute. Click here for details. A type with a mounting plate has been added. For the adsorption transfer of thin cloths, films, printed circuit boards, etc.
VQ1000-FPG-C4M5-D: 6 sets Double check block 757 S0700 Series Construction Body Ported Construction 2(B) (A)4 S0716 2-Position Single r u e w q 3(R2) (R1)5 1 (P) t y i 2-Position Double S0726 2(B) (A)4 r u e w q 3(R2) (R1)5 1 (P) t y i 3-Position Closed Center S0736 r u e w q 2(B) (A)4 (R1)5 1 (P) 3(R2) t y i 4-Position Dual 3-Port Valve S07A6 r u e w q 2(B) 4(A) 5(R1) 3(R2) 1(P) N.C. + N.C
Since a large quantity of liquid will be pumped out, use a suitable throttle in the discharge port if problems occur. Note 3) With a low number of operating cycles, even a valve with a small Cv factor can be operated.
Avoid using in a place where ventilated air from an air conditioner is directly applied to the product. g. Avoid using in a closed place without ventilation. h. Avoid using in direct sunlight or radiated heat. i. Avoid using in a place where there is a strong magnetic noise (strong electric field, strong magnetic field, or surge). j.
A B C A B A B A B A B Application Same tubing size 1 2 1 2 1 2 3 1 2 1 2 1 2 Refer to the applicable tubing table.
LOUIS, MO (314) 209-0080 CINCINNATI, OH (859) 647-5600 HOUSTON, TX (713) 460-0762 MILWAUKEE, WI (414) 827-0080 NEWARK, NJ (908) 253-3241 RICHMOND, VA (804) 527-0500 BINGHAMTON, NY (607) 773-1300 TAMPA, FL (813) 243-8350 CLEVELAND, OH (330) 963-2727 ROCHESTER, NY (716) 321-1300 BOSTON, MA (978) 326-3600 TULSA, OK (918) 252-7820 Business Deve lopment Cente r , I n d i a n a p o l i s, I N
If a moment or torque directly acts on the cylinder, it will lead to reduced service life or damage to machinery. 10-10-8 9 3 Position Cylinder Series RZQ Construction u i @2 r !0 y q w !9 e @1 @4 !3 RE A B @0 REC !2 CX @3 !
+ A = 100 y, z + A 100 10 y, z + A = 200 y, z + A = 200 y, z + A = 300 y, z + A = 300 1 1 0 200 400 600 800 1000 1200 0 100 200 300 400 500 600 700 800 Stroke [mm] Stroke [mm] [Graph 6] Allowable load mass by stroke 32 [Graph 5] Allowable load mass by stroke 25 100 100 y, z + A = 0 y, z + A = 0 y, z + A = 50 y, z + A = 50 10 Load mass [kg] Load mass [kg] 10 y, z + A = 100 y, z + A = 100
A B C A B A B A B A B 15A 20A 25A Note 1) For each piping diameter for each body size, the second and later numbers or symbols indicate reducing.
Refer to the Specific Product Precautions for the replacement period. 1517 A CY1L Series Construction Slider type/Ball bushing bearing CY1L6 $0 #9 #3 @2 t #4 !9 #8!0!2!6 @4 @1 @8 #0 #1 $1 w @9 i #2 !1 o q u r y e @6 @5 @3 @7 CY1L10 to 40 @2#9 @0$0 t !9 #5$2 #8 !2 !0 !6!7@4 @1 !8 !4 !5 $0 @8 #7 #6 $1 F G Area G (10) Enlarged view F 10, 15 w u i o !1 #2 q !
Use a straight bladed watchmakers' screwdriver for the set trimmer to turn it softly. Use a straight bladed watchmakers' screwdriver to adjust the set trimmer for I(Z)SE1/I(Z)SE2/PS100. Turn it softly, but do not turn more when reached to the stopper at both ends. If a trimmer were broken, it would be impossible to adjust it. 6.