Series KV2 Fittings Operating Pressure Air 145psi (1.0MPa) Size At 75F (24C) At 200F (93C) 3/8 1/4 1/2 5/32 5/8 3/4 1400psi 1200psi 950psi 1200psi 900psi 800psi Proof Pressure 450psi (3.1MPa) Recommended Fluid and Ambient Temperature* -40F to 140F (-40C to 60C) 7 Ncm/min. or less Leak Rate at -40F (-40C) Thread Portion Nut ANSI/ASME B1.20.1, 1983, R1992 Thread JIS B 0208 (Unified fine thread), ISO 263 Thread
Also, store it where it can be referred at any time. Fitting Caution 1. A fitting with an O-ring is used for a high vacuum rodless cylinder. Use a fitting that conforms to the dimensions below, and install it so that there is no air leakage. P (Port size) Operation P (Port size) Model CYV15 CYV32 Caution 5/16-24 UNF 7/16-20 UNF 1.
10mA load current) 0.8V or less 4V or less Internal voltage drop 100A or less at 24VDC 0.8mA or less at 24VDC Leakage current Operating position .
Never use pressure sensors in the presence of inflammable or explosive gases. 20 Series PSE Specific Product Precautions 2 Be sure to read before handling. Refer to pages 17 through 19 for general safety instructions and common precautions, and to pages 20 through 22 for specific product precautions.
Never remove valve at an angle.
II Air Cylinder Drive Systems Total Stroke Time and Speed at the End Series SV Series SV1000 Applicable bore size: 20, 25, 32, 40 Applicable related components Total stroke time s Solenoid valve Tubing Speed controller Silencer 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 200 CM2 20 50% 70% 10% 30% 150 Stroke mm AS2201F -01-06 AS2200-01 70% 100 50 10% 30% 50% 0 200 CM2 25 150 Stroke mm AS2201F
In all cases, with the exception of NPT, add -X2025 at the end of the order number.
(mm) H1 6 7 8 11 11 H 36 40 45 53 56 GY 5 5.5 7 8 10 GX 10 8.5 9 11.5 11.5 EY 26 42 54 64 72 D 12 14 16 20 20 B1 17 19 22 27 27 C 54 68 86 104 124 B 24 28 32 39 50 BY 7 8 9 9 12 AL 19.5 23.5 27 32 32 BX 9 6.5 8 10 11 ET A 22 26 30 35 35 BS 42 50 54 64 63 K 5.5 5.5 6 7 7 BT Model MUB25 MUB32 MUB40 MUB50 MUB63 Standard stroke (mm) 5, 10 5, 10 5, 10, 15, 20 5, 10, 15, 20 5, 10, 15, 20 M5 x 0.8
X 500 500 500 500 0 0 0 0 10 20 30 40 50 0 0 2 4 6 8 10 12 14 16 0 4 8 12 16 20 24 0 10 20 30 40 50 60 Work load [kg] Work load [kg] Work load [kg] Work load [kg] 2000 2000 2000 2000 Mey 1500 1500 1500 1500 L5 [mm] L5 [mm] L5 [mm] L5 [mm] m 1000 1000 1000 1000 Wall L5 Y 500 500 500 500 0 0 0 0 4 8 12 16 20 24 0 10 20 30 40 50 0 0 2 4 6 8 10 12 14 16 0 10 20 30 40 50 60 Work load [kg] Work
A quick recovery time indicates little liquid pool. 50 Ratio of resistance [k m] Particle ratio [number/cc] PFMC 100 2 or 3 particles/cc PFMV 10 00 10 20 30 40 50 60 70 PF2A 1 0 5 10 15 20 25 30 Duration of flow [min] Duration of flow [hour] PF3W The data was obtained by performing an actual 10 minutes supersonic cleaning using an average 16 Mcm of deionized water at class 10 clean room
Green lights ON at optimum detecting position.
Set the supply pressure at 0.25 to 0.5 MPa. If setting at less than 0.25 MPa, malfunction of the release brake may occur. If line pressure is used directly as supply pressure, any fluctuation in pressure will appear in the form of changes in cylinder characteristics.
Set the supply pressure at 0.25 to 0.5 MPa. If setting at less than 0.25 MPa, malfunction of the release brake may occur. If line pressure is used directly as supply pressure, any fluctuation in pressure will appear in the form of changes in cylinder characteristics.
Description Material 40 NLP-40A PDU-16Z PSD-22 x 16 P44 DSM-20 CA40-1606 CA40-1601 P3 50 NLP-50A PDU-20Z PSD-27 x 20 P50 DSM-25 CA63-1608 CA50-1602 P3 63 NLP-63A PDU-20Z PSD-27 x 20 P60 DSM-25 CA63-1608 CA63-1603 P3 100 NLP-100A PDU-30Z PSD-38 x 30 P90 DSM-35 CA100-1610 CA100-1605 P5 Piston seal Rod seal A Rod seal B Brake piston seal Cushion seal Piston gasket Tube gasket Cushion valve seal
(M4 x 20) (Tightening torque: 0.7 to 0.8 Nm) The tightening torque at the valve side depends on the valve type. Refer to the operation manual of the corresponding valve manifold.
Also, store it where it can be referred at any time. Fitting Caution 1. A fitting with an O-ring is used for a high vacuum rodless cylinder. Use a fitting that conforms to the dimensions below, and install it so that there is no air leakage. P (Port size) Operation P (Port size) Model CYV15 CYV32 Caution 5/16-24 UNF 7/16-20 UNF 1.
(Order separately) Note 2) Mount so that the exhaust cleaner is at the lower side.
Test was performed at both energized and deenergized states in the axial direction and at the right angles to the main valve and armature.
Operation at the stroke beyond the max. stroke could cause breakage of piston rod.