I FS Max Air Supply Pressure at 1MPa <9.5l/min (Bleed P) <4l/min <9.5l/min Consumption at 0.7MPa <2l/min (EXH) <3l/min <2l/min at Max Gauge Port Size 1/8 (2 Ports Front/Back) 0 IR Ambient & Fluid Temperature -5 ~ 60C / 23~140F (with no freezing) B O D Y S I Z E 1 IR1000 2 IR2000 3 IR3000 S U F F I X R Pressure Gauge on the Opposite Side * The Standard Mounting Piston of the Pressure Gauge
Mount a switch at the center of the operating range. Adjust the mounting position of an auto switch so that the piston stops at the center of the operating range (the range in which a switch is ON). (The mounting positions shown in the catalog indicate the optimum position at stroke end.)
Parameter Set value Initial value Note Fixed For the EXW1-RD#, the number is fixed at 16 (16 bits). * Although the number of occupied inputs of EXW1-RDM# is fixed at 16 (16 bits), only the lower 8 bits are available.
Input units can be added or removed at the point of use without rewiring or re-addressing.
Confirm that the green LED is on when stopped at the established position.
Recommended valve/for PB1013 air operated type: SYJ34 Note 2) After initial suction of liquid operating at 1 to 7Hz, it can be used with operation at lower cycles.
(Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 1000 Hz. Test was performed at both energized and deenergized states in the axial direction and at the right angles to the main valve and armature.
Later the operation restarts and then stops at the first zero signal to complete the machine OPR.
600 V, are used at an ambient temperature of 30C.
Note 4) Air ow capacity under the standard condition (ANR) [at 20 Air ow capacity under the standard condition (ANR) [at 68F (20C), atmospheric pressure, relative humidity 65%] Note 5) Air ow capacity converted by the compressor intake condition [at 90F (32C), atmospheric pressure] Note 6) Dew point of the outlet air pressure shown in this table is the value that is obtained when the air
Cuts air consumption by operating the return stroke at a reduced pressure.
This saves additional electrical wiring at the time of installation.
Intermediate strokes For manufacture of strokes other than the standard strokes above, add "-X2" at the end of the part number.
Operation at the stroke beyond the max. stroke could cause breakage of piston rod.
to cylinder, Needle fully open (2) Load ratio {(Load weight x 9.8) Theoretical output} x 100% Speed at the end (u) Time (s) SOL: ON(OFF) 1-2-4 1-2-5 4 Series SV Air Cylinders Drive System Full Stroke Time and Speed at the End Air Cylinders Drive System Full Stroke Time and Speed at the End Series SV3000 Applicable bore size: 50, 63, 80, 100 Series SV4000 Applicable bore size: 63, 80, 100
Yellowish green Actuator is operating. (1-7) Current step data The current step data number or the step data number which was previously used is indicated at the bottom of the main window display. (1-8) Communication status The communication status between the controller and the PC is indicated at the bottom of the main window display.
100 mA) Max. applied voltage: 26.4 VDC Max. load current: 100 mA Residual voltage 1 V or less (Load current at 100 mA) Max. applied voltage: 26.4 VDC Maintenance detection signal Max. load current: 100 mA Residual voltage 1 V or less (Load current at 100 mA) Max. load current: 100 mA Residual voltage 1 V or less (Load current at 100 mA) Output signal Error signal Offset voltage control
In locations at altitude of 3000 m or higher (Except during storage and transportation) * For altitude of 1000 m or higher Because of lower air density, the heat radiation efficiencies of the devices in the product will be lower in the location at altitude of 1000 m or higher.