Speed Controller with One-touch Fitting for Clean Room Series AS-FPQ/AS-FPG T M5 type H (width across flats) Applicable tubing O.D. d A A4 D1 L3 D2 M1 L1 T L2 Model Weight (g) Note 2) Tubing O.D. d T H D1 D2 L1 L2 L3 M1 L4 Max.
Installation at indoor site (for air cooled type) 1. For a facility having a large installation area (that can vent the air naturally): Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2.
Installation at indoor site 1. For a facility having a large installation area (that can vent the air naturally): Make an air outlet on a wall at a high level and air inlet on a wall at a low level, to allow for adequate airflow. 2.
The product operation at the time of alarm AL21 can be selected. This function is set to [ ] (stop) at the time of alarm by default.
10mA load current) Internal voltage drop Leakage current 100A or less at 24VDC 0.8mA or less at 24VDC Operating position .
At this time, Monitoring (RXn8) turns to ON at the same time.
At this time, Monitoring (RXn8) turns to ON at the same time.
Speed at a rated motor rotation of 3000rpm Accel.
Supply Pressure Set the supply pressure at 0.25 to 0.5 MPa. If setting at less than 0.25 MPa, malfunction of the release brake may occur. If line pressure is used directly as supply pressure, any fluctuation in pressure will appear in the form of changes in cylinder characteristics.
Fingers synchronized by a rack and pinion mechanism Model/Stroke Max operating frequency (c.p.m) Opening/closing stroke (L2L1)(mm) Weight (g) Width at closing (mm) (L1) Width at opening (mm) (L2) Bore size (mm) Model Built-in dust proofing mechanism 60 20 40 60 30 60 80 40 80 100 50 100 120 70 120 160 100 160 200 56 78 96 68 110 130 82 142 162 100 182 200 150 198 242 188 246 286 76 118 156
Set the supply pressure at 0.25 to 0.5 MPa. If setting at less than 0.25 MPa, malfunction of the release brake may occur. If line pressure is used directly as supply pressure, any fluctuation in pressure will appear in the form of changes in cylinder characteristics.
Set the supply pressure at 0.25 to 0.5 MPa. If setting at less than 0.25 MPa, malfunction of the release brake may occur. If line pressure is used directly as supply pressure, any fluctuation in pressure will appear in the form of changes in cylinder characteristics.
Easy control at low speeds Effective area of controlled flow is about one tenth of the standard series. Suitable for control of low speed cylinders at 10 to 50mm/sec. Operating strokes at low speed and return strokes at high speed Effective area of free flow units are the same as standard.
Displacement at "A" when a load is applied to "F" with the slide table retracted. Displacement at the section indicated by the arrow when a load is applied to this section with the slide table fully extended.
accessory E: 110 At accessory F: 110 { } 5 150 194 125 G1/2 Electric conduit 35 At accessory E: 195 At accessory F: 275 { } 4 x M8 x 1.25 depth12 (Female thread for rear mounting) With optional resin cable clamp Applicable cable O.
(page at left) Suffix -XB10 to the end of standard model no. (page at left) Rubber bumper is standard equipment for long stroke type. Part no. Mounting Bracket Part No. Intermediate strokes by the 1 mm interval are available by using spacers with standard stroke cylinders.
Consult SMC concerning water resistance, flexibility of lead wires, and usage at welding sites, etc. 98
Therefore, when used at near the upper limit, the following guide will be helpful.
Never remove valve at an angle.
Therefore, when used at near the upper limit, the following guide will be helpful.