<br>Information on industrial filter selection can be found here.<br>The differences between the 2 are as follows. <br>Seal material: Select from NBR or FKM for the FQ1 series and NBR or fluororesin for the FGD series.<br>Housing material: Only stainless steel 304 is available for the FQ1 series.

,,: ,.

R6teren@ torque sDecificalion Tabl *3 '11 lflU / [[U $enies D0I/$[EfirHu Union 'Y': KVU*_ OO l02C / lffi / lflP $mics D0I/8[EthHt Caps: KQ2C Fitting Boot: KR 6D r-'---t-1 Plugs: KVP 1 2 D0r/$uffnFll|lnm tul $enie Cartridge: KVOA DOT Specilications Tabl 1 Not alaihu at lim6 of cablog prinling, Corbult hdory br a\bilability.

Magnet: D (Built-in), Mounting: B [Through Hole (Standard)], Bore Size: 50mm, Port Thread Type: Rc, Stroke: 40mm, Body Option: Rod End Female Threads, Standard, Locking Direction: B (Retraction Locking), By-Pass Piping: None (Emergency Stop), Auto Switch: M9P--Solid State, Gen. Purpose, 3 Wire PNP, Horizontal, Lead Wire or Prewired Connector: SAPC (0.5m Cord Length, M8-3 Pin Connector)

Magnet: Built-in, Mounting: B [Through Hole (Standard)], Bore Size: 50mm, Port Thread Type: Rc, Stroke: 40mm, Body Option: Rod End Female Threads, Standard, Locking Direction: Retraction Locking, By-Pass Piping: None (Emergency Stop), Auto Switch: M9P--Solid State, Gen. Purpose, 3 Wire PNP, Horizontal, Lead Wire or Prewired Connector: 0.5m Cord Length, M8-3 Pin Connector, Number: -

<br>These valves can be used for stopping a cylinder at an intermediate position, vacuum suction, vacuum break, and selector valves and divider valves.<br>Further details on the VEX3 series can be found here.

<br>Note 1) Air of up to 9.5 L/min (ANR) [at a supply pressure of 1.0 MPa] is constantly exhausted (consumed) from the PE port for high-precision pressure regulation. <br>Note 2) Install a mist separator on the supply side in addition to the filter. <br>Note 3) When the outlet pressure is higher than the set pressure, the R port is used for exhaust until the set pressure is reached.

<br>Note) For a single unit single solenoid, exhaust is not performed from the Y port (the side without a pilot valve).<br><br>

<br>For the new type, there is a “1” added after the symbols for voltage, electrical entry, and manual override method.<br>The low-wattage type “Y” is now the standard specification, so a “Y” is no longer required in the part number.<br>Note) For the SQ2231D-5-C6, the product with an equivalent response time is the SQ2231BD-51-C6. (The type with a “B” is the high-speed response type.)

<br>No internal seals are available.<br>For the SQ1000, the part number is “SQ1000-GS” (10 pcs./set, with screws). <br>And for the SQ2000, the part number is “SQ2000-GS” (10 pcs./set, with screws).

<br>The 4-pin DIN connector (D(Z) type) part number is “GDM3D.” (The optional gasket part number is “DXT087-27-2.”)<br>The 3-pin DIN connector (D(Z) type) part number is “B1B09-2A6.” (The optional gasket part number is “CAXT623-6-7-12.”)<br>And the 3-pin DIN connector (Y(Z) type) part number is “GMN209.” (The optional gasket part number is “CAXT623-6-7-13.”)

<br>For normally closed use: Plug the B port and pipe to the A port. <br>For normally open use: Plug the A port and pipe to the B port.<br>Note) Do not plug the exhaust ports (EA or EB); instead, mount a silencer. (The same goes for the PE port.)

<br>Therefore, they can be used as selector valves or as divider valves.<br>Note) When using different pressures, use within the specified pressure range of the product.<br>The VT307, VT317, and VT325 series catalogs can be found here.

<br>The value is the same for the valves for manifold of each of the following series: VO307□, VO317, VO325, and VO315.<br><br>

<br>The part number is “VM220-02-40A” (for the 2-port type) or “VM230-02-40A” (for the 3-port type).<br>Select the one that best suits your application. A 5-port type is also available with the special order part number suffix “-XT34-60” or “-XT34-67.”<br>Further details are available at the end of the VM/VZM/VFM series catalog, which can be found https://www.smcpneumatics.com/Part-Builder-Links_ep_2458-1.html?https://smccatalog.partbuilder.smcpneumatics.com/support/faq/en-jp/?ca_id=directional-control-valves&fa_id=10634