Compact Type Therefore, do not use a cylinder without a bumper bolt. Furthermore, if the bumper bolt is tightened without a nut, the piston seal is caught in the leveled part, damaging the seal. 3. A bumper at the end of the bumper bolt is replaceable. In case a missing bumper, or a bumper has a permanent settling, use a following part numbers for ordering.
When a load, such as a relay or solenoid, which generates surge is directly driven, use a type of switch with a built-in surge absorbing element. 8.
A + A' A' w After piston seal H has passed air passage A, air is exhausted only through A'. The section marked with slanted lines becomes a cushion chamber, and an air cushion effect is achieved. A A' A' e When air is supplied for the piston extension, the check valve opens and the piston extends with no delay.
Do not use this product on board a vehicle or a vessel. This product must not be installed and used on board a conveyance such as a vehicle or a vessel, as it may become damaged due to vibration. If it must be used in such a manner due to unavoidable circumstances, please contact SMC beforehand. 1.
B 220V Dryer Capacity Model A Part No.
Note 3) A particulate generation test has been conducted in a vacuum environment of 10-Pa. a t e l u g c 2 Stainless steel linear guide & low particulate generation vacuum grease e i t n r a e p r a 0.0 10 0 20 10 w t i o o n L Operation cycles a t e l u g c e 1 i t n r a e Particulate generation from the linear guide unit has been reduced with the use of a stainless steel linear guide and
Consider selecting a ZNC series (body size 20) Bernoulli gripper as a substitute. Click here for details. A type with a mounting plate has been added. For the adsorption transfer of thin cloths, films, printed circuit boards, etc.
Each step is accompanied by a guidance box that will bring up instructions in a dialog box. The Wizard is a learning tool and does not possess the full capabilities of programming on the FBD Base.
Description B VNH1 VNH2 VNH3 VNH4 VNH1-16 VNH2-16 VNH3-16 VNH4-16 Bracket (with bolt and washer) 4.2-30 VNH Specifications 3 port valve 2 port valve A B A B VNH311 20A A B VNH411 25A A B VNH113 10A A B VNH213 15A A B VNH313 20A A B VNH413 25A A B VNH133 10A A B VNH233 15A A B VNH333 20A A B VNH433 25A A B VNH111 10A VNH211 15A Model Operating fluid pressure Fluid Operation 0 to 7.0MPa 0 to
Caution Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Warning Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
N.O. 1 (P) 3 (R) 1 (P) 3 (R) a c e d a c e d (A) (A) 2 2 g g 3 (R) 1 (P) 3 (R) 1 (P) b b f f Component parts Replacement parts Note Zinc die-casted No.
If driving a load such as a relay that generates a surge voltage, use a switch with a built-in contact protection circuit or use a contact protection box. 1) For an auto switch without a contact protection circuit, use a contact protection box when the wire length is 50m or longer.
ao . , , , , t o o 3 . , , . , 05 stePping a ''.a: ' , . a , : a : l r : : i : l ::: I iob' ' ', ' t99;:9i1':i1:t t: llli,2.gtepping O8: 12mm lead , , . , , 1 ( } . u 5 asbinriea,i : r iri llliqq'i'' o5 stepoinq 30 08; zmm lead o2 stepping 80 08; 5mm lead 10.03 30 08; 2mm lead s5 stepping 80 08; 5mm lead a I a a a 100 O8; 6mm lead o2 stepping I M <-iD;;,;; uo200 08; 12mm lead 10.05 100 08
D-F9WV D-F8 Model A B C D E A B C D E A B C D E A B C D E A B C D E A B C D E A B C D E A B C D E 18.5 31 6.5 20.5 41 8.5 20.5 33 4.5 17 20.5 31 4.5 15 20.5 41 4.5 15 20.5 51 4.5 35 22.5 43 6.5 27 22.5 33 6.5 17 22.5 43 6.5 27 22.5 53 6.5 37 MIW12-12D MIW20-20D 6 4 4 2 18.5 29 6.5 20.5 31 8.5 MIS12-10D MIS20-10D 4 2 6 4 2.5 4 18.5 39 6.5 20.5 41 8.5 MIS12-20D MIS20-20D 6 4
C C RHC D D Note) Be sure to use a flat washer for the type A mounting.