MXQ A malfunction may occur with a control circuit that exhausts from both ports, such as exhaust center 3 position valves. 1. When mounting the air slide table with buffer it must be oriented as shown in the sketch below. In horizontal operation, the buffer may travel the stroke length and activate the auto switch depending on the load and the speed.
At higher temperatures, breakage or flattening may occur even with a value larger than the minimum bending radius.
When the valve is closed, and pressure exceeding maximum operating pressure is applied suddenly due to the starting of fluid supply source such as a boiler, the valve may open momentarily and fluid may leak. 17 These safety instructions are intended to prevent hazardous situations and/or equipment damage.
The period may vary depending on the temperature and other conditions. In some cases the absorber may need to be replaced before the allowable operating cycle above. Model Bolt Max. tightening torque Nm Max. screw-in depth l (mm) MXY6 MXY8 MXY12 3 4 5 1.14 2.7 5.4 M3 x 0.5 M4 x 0.7 M5 x 0.8 D9. Be careful not to bruise the outer surface of the cylinder tube.
The product specified here may become unsafe if handled incorrectly. The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced. here may become unsafe if handled incorrectly. here may become unsafe if handled incorrectly. here may become unsafe if handled incorrectly.
The product specified here may become unsafe if handled incorrectly. The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced. here may become unsafe if handled incorrectly. here may become unsafe if handled incorrectly. here may become unsafe if handled incorrectly.
If the tightening torque is exceeded the mounting screws may be broken. IP67 protection cannot be guaranteed if the screws are not tightened to the specified torque. If a large manifold valve is mounted, lift the unit so that stress is not applied to the connecting part while transporting. The stress may cause breakage of the connecting part.
If the tightening torque is exceeded the mounting screws may be broken. IP67 protection cannot be guaranteed if the screws are not tightened to the specified torque. If a large manifold valve is mounted, lift the unit so that stress is not applied to the connecting part while transporting. The stress may cause breakage of the connecting part.
If using other screws, switch may be damaged.
Otherwise, the life of the contacts may be reduced. (They may stay on continuously.)
Do not use tools on the pressure regulator knob as this may cause damage. It must be operated manually. Caution 1. Be sure to unlock the knob before adjusting the pressure and lock it after setting the pressure. Failure to follow this procedure can cause damage to the knob and the outlet pressure may fluctuate. Warning 1.
When 2 swilches are cohnected as OR, load voltage *,ill increase at OFF and these conneclions may cause mallunction.
If the tightening torque is exceeded the mounting screws may be broken. IP67 protection cannot be guaranteed if the screws are not tightened to the specified torque. If a large manifold valve is mounted, lift the unit so that stress is not applied to the connecting part while transporting. The stress may cause breakage of the connecting part.
Note 1) Since static electricity may be generated, implement suitable countermeasures. Note 2) Fluid may pass through. Fluid that has passed through may have an impact on components made of different materials. Table symbol : Can be used : Can be used under certain conditions Compatibility is indicated for fluid temperatures of 60C or less.
The set pressure may vary depending on the elapsed time and change in ambient temperature after pressure setting. If the setting value varies, adjust with the knob. 7. If the directional control valve (solenoid valve, mechanical valve, etc.) is mounted and ON-OFF is repeated for a long time, the set pressure may vary. If the setting value varies, adjust with the knob. 8.
The product specified here may become unsafe if handled incorrectly. The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced. 1.
Combination of K and V (Only one or the other may be attached.) Note 2) Standard specification is the power cable with plug.
Do not use a tool to mount the connector, as this may cause damage. Only tighten by hand. (0.4 to 0.6N) SY100-68-A 3. Do not apply excessive power greater than 30N to the connector cable, otherwise IP65 cannot be satisfied.