Compact Hydraulic Cylinder Double Acting/Single Rod Series CH QB ø 20, ø 32, ø 40, ø 50, ø 63, ø 80, ø 100 Since Series CHQB does not have an air release plug, release air from other components (e.g. from piping, etc.) as well. 6. When mounting the cylinder body with mounting bolts, use the tightening torques in the table at right as a guide.
The operating load is an induction load. 2. The length of wiring to the load is 5m or more. 3. The load voltage is 100VAC. A contact protection box should be used in any of the above situations. Otherwise, the life of the contacts may be reduced. (They may stay on continuously.)
06 10 06 10 90 M6 x 1 Depth 7.5 39 50 0 77 74 59 175 128 3/4, 1 46 06 10 107 06 10 94 M6 x 1 Depth 7.5 39 50 0 77 74 59 175 128 3/4, 1 46 06 10 111 5 Soft Start-up Valve AV2000/3000/4000/5000 Modular F.R.L.
Note 2) Impact resistance: No malfunction when tested with a drop tester in the axial direction and at right angles to the main valve and armature, one time each in both an energized and deenergized state.
VN Valve option Nil V Standard For vacuum, non-leak LVC LVA Select an option mark in page 17-3-14 by Applicable Fluids Check List for special fluids outside of the standard. LVH LVD Table (1) Port/Orifice Size Valve (Port size) Orifice size (No.)
Order Made Power Saver Power consumption is decreased by 1/3 reducing the wattage required to hold the valve in an energized state. (When the rated 24V DC is applied, its effectiveness will be exhibited at an energization time exceeding 62ms.) Operating principle Specifications SY The circuit shown below reduces current consumption at holding which reduces the overall power consumption.
IISA2NPL-1D1 set (1 station manifold part number) ISA2-GE41N 1 set (Air catch sensor part number) Prefix the part number of the air catch sensor with an asterisk (). Prefix the part number of the air catch sensor with an asterisk ().
MSQ Angle adjustment Range Figure 5 MSZ MSZ CRQ2X MSQX ad a ge ju Cl lt MRQ an st bo oc t r m nd en g k en tm wi in e us 10 10 se t r st on dj a ju an r on ti ot ad iti ta os ge at p ro er y nt io e b C e b n y is e ge n ad w d k an c ju lo t r C st in en g m bo st lt ju b ad M 0 ax 19 im e u ng m ra ro n ta tio Center position adjustment Table 2 R: Clockwise adjustment L: Counterclockwise
It is equivalent to the pilot lamp of an electrical system. This is an ultra-compact air indicator light to monitor the presence of air pressure. It is equivalent to the pilot lamp of an electrical system.
M2 M3 m1 m2 m3 16 25 40 16 25 40 7 6 7 15 13 13 MY2H 28 26 26 32 30 30 60 50 60 62 62 62 46 55 46 20 18 18 100 120 100 38 35 35 MY2HT 200 220 200 80 80 80 The above values are the maximum allowable values for moment and load. Refer to each graph regarding the maximum allowable moment and maximum allowable load for a particular piston speed.
The cushion effect (smooth start-up, soft stop) cannot be obtained in an intermediate stop or return from an intermediate stop using an external stopper, etc. The load should be guided by a ball type bearing (LM guide, etc.). If a slide bearing is used, sliding resistance increases due to the load weight and load moment, which can cause malfunction.
Method (Operation example with an energy saving driver circuit) 2.
An angled supply port facilitates the supply of circulating fluid, even when units are stacked. A large digital display provides a clear view of the current and set values.
.' 80 46 .5 55 46.5 52.5 ; 100 55 62 55 59.5 Reed Type With Conduit Auto Switch Mounting Position And Height (mm) ~ Bore Size Il-A44 J (mm) A B H.
I Compact Guide Cylinder with One-way Lock Series MLGP 40, 50, 63 Prevents dropping when air supply pressure falls or residual pressure is exhausted Can be locked at any position The locking position can be changed to accommodate an external stopper position or the thickness of clamped work pieces, etc.
arm length of 200 mm and an operating pressure of 0.5 MPa, according to the graph, the maximum clamping force is 2000 N.
Format error 39 An error is found in the attached value of a command being programmed. Refer to the Series LC1 instruction manual for alarm details.
Displacement may increase after an impact load has been applied. When the table is subjected to an impact load, there may be permanent distortion of the guide unit and increased displacement.
Please contact P/A if hysteresis causes an operational problem. 15 Auto Switch Connections and Examples Basic Wiring 2-wire Solid state 3-wire, NPN (Solid state) 2-wire Solid state 3-wire, PNP (Reed switch) Brown Brown Brown Brown Load Load Indicator light Protective circuit etc.
Our pressure switches do not have an explosion proof rating. Never use in the presence of an explosive gas as this may cause a serious explosion. 1. Do not drop, bump, or apply excessive impacts (980 m/s2) while handling. Although the body of the sensor may not be damaged, the internal parts of the sensor could be damaged and lead to a malfunction. 2.