AS-FPQ/AS-FPG AS-FG AS-FP AS-FP AS-FM AS-D AS-T ASP ASN AQ ASV AK VCHC ASR ASQ 715
AS1001FG-04-X214 ASV AK Needle Valve/Flow Characteristics VCHC Note) The flow characteristics are representative values.
The following check valves are available: AK Series, AKH/AKB Series
In addition, special order check valves for SUS bodies, high/low temperatures, etc., are available: AK Series, AKH/AKB Series
For more information, refer to the AK series catalog, which can be found here.
To replace seals or grease the cylinder during maintenance, use an appropriate pair of pliers (tool for installing a type C snap ring for hole). After re-installing the cylinder, make sure that the snap ring is placed securely in the groove before supplying air. 2.
To replace seals or grease the cylinder during maintenance, use an appropriate pair of pliers (tool for installing a type C snap ring for hole). After re-installing the cylinder, make sure that the snap ring is placed securely in the groove before supplying air. 2.
0.25 0.375 0.25 0.073 an 0.948 an1 OK ML2B32 20 2.
When the work holding point is out of the limited range, the unbalanced load applied to the finger and the guide section may cause excessive play in fingers and have an adverse effect on the gripper life.
BUSY (11) Operating signal COM +24V 1 COM 11 GND NO.0 When this signal is off, an alarm is being generated for the actuator/controller.
VN LVC Prepare an insert bushing and nut for 1/8" O.D. tubing (LQ-2U03) and change the tubing size. (Refer to the section on how to order fitting parts.) LVA Note) Tubing is sold separately.
LVC Select an option mark in page 17-3-9 by Applicable Fluids Check List for special fluids outside of the standard. LVA LVH Connection 1 4 3 8 1 2 3 4 02 03 04 06 10 LVD Thread type Nil T F N Refer to the table (2) given below for availability.
LVC Select an option mark in page 17-3-10 by Applicable Fluids Check List for special fluids outside of the standard. LVA VXP2130: Option C, K, Q, S only.
Auto Switch Proper Mounting Position (Detection at Stroke End) Electrical entry direction: Inward Electrical entry direction: Outward D B A C B D-Z7Z8, D-Y7W D-Y5, D-Y7 D-Y6, D-Y7V D-Y7WV D-Y7BA Bore size (mm) A C 16.5 (15) 23.5 (22) 34 (32.5) 46 (44.5) 46 (44.5) 56 (54.5) D 0.5 (1) 3.5 (2) 0.5 (1) 3 (1.5) 5 (3.5) 5 (3.5) C 18 25 35.5 48 48 58 D 2 5 2 4.5 6.5 6.5 C 10.5 17.5 28 40 40 50 D
Can be disassembled (Series CG5-S) Replacement of seals promotes an extended service life. (Before disassembly, be sure to see the section regarding maintenance under "Specific Product Precautions" on page 32.)
44 44 58 41.5 46.5 99 44 66 18 36 67 31 8.5 12.5 28 18 12.8 M4 6 1/4 99 24 25 56.5 46 54.5 60 52 48.5 101 54.5 68 22 40 81.5 36.5 11 15 32 20 19 M5 8 1/4, 3/8 VCL31 104 24 25 59 46 57 60 54.5 48.5 101 57 68 30 50 84 36.5 13.5 15 32 25 23 M5 8 1/2 107 26 26.5 64.5 48 62.5 62 60 50.5 103 62.5 70 22 45 89 41 11 17 36 22.5 23 M5 8 1/4, 3/8 VCL41 111.5 26 26.5 66.5 48 64.5 62 62 50.5 103 64.5
AXT620-32-1 (M4 x 48, With spring washer) For mounting valve M4: 1.4 Nm 1509 VFA3000/5000 Series Dimensions: VFA3000 Series/Base Mounted 2 position single VFA3140(-P) 02 03 2 position double VFA3240(-P) 02 03 28 33 28 33 1/4, 3/8 [4 (A), 2 (B) port] 1/4, 3/8 [4 (A), 2 (B) port] 13 13 22 22 1/8 (Pilot port: Upward) 81 1/8 (Pilot port: Upward) 46 20 36 36 20 46 4A 2B 4A 2B 26.4 26.4 35 42
Manifold Option JIS symbol Blanking plate assembly VVCW 1486 3A 2 K Series Material 2 3 4 Class 2 Class 3 Class 4 Plate material Seal material PTFE FKM Symbol K H Stainless steel This is used by mounting it on the manifold block when a valve is removed for maintenance or when the mounting of an additional valve is planned, etc. 17-2-46 9 Series VCS Direct Operated 2 Port Solenoid Valve For
Mounting of Auto Switch When mounting an auto switch, insert it into the cylinder's switch groove from the direction shown in the figure below. After setting it in the mounting position, use a flat head watchmakers screwdriver to secure it with the mounting screw which is included.
Note 3) An optional specification for special wiring is available to increase the maximum number of stations.
When the gripping point distance becomes large, the finger attachment applies an excessively large load to the finger sliding section, causing excessive play of the fingers and possibly leading to premature failure.
When the gripping point distance becomes large, the finger attachment applies an excessively large load to the finger sliding section, causing excessive play of the fingers and possibly leading to premature failure.