Functional ground (When the driver is mounted, tighten screws and connect the grounding cable) (10) FG 18 - 3.3 Outside dimension diagram The outside view of this product is as shown in the diagram below: (1) Screw mount type (LECPA-) (2) DIN rail mount type (LECPAD-) 19 - 3.4 How to install (1) How to install The driver can be direct mounted using screws or mounted on a DIN rail.
Applicable cable of the communication connector Cable cross section 0.2 mm2 to 2.5 mm2/AWG24 to 12 Communication connector Terminal Wire colour Connection VBlack (-) side of DeviceNetTM power supply cable CANL Blue Low side of communication cable FG (DRAIN) Ground / Shield wire CANH White High side of communication cable V+ Red (+) side of DeviceNetTM power supply cable Note Wiring should
(Refer to the installation manual) Connect frame-ground terminal (FG terminal) to the ground when using a switching power supply. Do not drop, hit or apply excessive shock (larger than 1000 m/s2) to the Auto switch. Otherwise it can result in damage to the Auto switch causing failure or malfunction. -5No.D-S-OMB0023-C Wiring Do not pull the lead wires.
Be sure to ground terminal FG when using a commercially available switch-mode power supply. Do not drop, hit or apply shock to the Pressure Sensor. Otherwise damage to the internal parts can result, causing malfunction. Do not pull the lead wire forcefully, not lift the product by pulling the lead wire.
Be sure to ground terminal FG when using a commercially available switch-mode power supply. Do not drop, hit or apply shock to the Pressure Sensor. Otherwise damage to the internal parts can result, causing malfunction. Do not pull the lead wire forcefully, not lift the product by pulling the lead wire.
Be sure to ground terminal FG when using a commercially available switch-mode power supply. Do not drop, hit or apply shock to the Pressure Sensor. Otherwise damage to the internal parts can result, causing malfunction. Do not pull the lead wire forcefully, not lift the product by pulling the lead wire.
If a commercially available switching power supply is used, be sure to ground the frame ground (FG) terminal. Do not drop, hit or apply excessive shock to the product. Otherwise damage to the internal parts of the product, solenoid valve and internal parts of the pressure switch/sensor can result, causing malfunction.
contact (CLOSE During Alarm) Alarm Output Temperature Alarm a connector 6 7 8 9 6 contact (OPEN During Alarm) D-sub 9 pin (Pin type) 7 Temperature Alarm Fixed screw: M2.6 Common Temperature Alarm b 8 contact (CLOSE During Alarm) 3 Resistance Bulb Terminal A 8 1 4 Resistance Bulb Terminal B External temperature 5 Resistance Bulb Terminal B 15 9 sensor D-sub 15 pin (Socket type) connector 15 FG
Terminal block arrangement A-phase pulse input B-phase pulse input Bank 1 selection Bank 2 selection (UP pulse) (DOWN pulse) Sensor power Sensor power FG terminal Control input Sensor input Sensor input Reset input Hold input common common common output GND DC12V ..
(j) (d) FG (k) (l) (e) Mode switch Swich the mode between manual and auto. (m) Auto mode / Without alarm: Indicates the position number which is command by ON/OFF of IN0 to IN3 of the CN4 parallel I/O. (During command operation: Flashing / Instruction command completed: ON) Auto mode / With alarm: Indicates Alarm Group.
Ensure that the FG terminal is connected to ground when using a commercially available switchmode power supply. Do not drop, hit or apply excessive shock to the product. Otherwise damage to the internal parts of the product, solenoid valve and internal parts of the pressure switch can occur, causing malfunction.
CN9 SDI1A+ 1A 1B SDI1AMC Driver Servo amplifier SDO1A+ 4A CN8 Control circuit 4B SDO1ACN8A STO1 4 STO2 5 CN10 3A SDI2A+ STOCOM 3 3B SDI2ATOFB1 6 1A SRESA+ 1B SRESATOFB2 7 6A SDO2A+ TOFCOM 8 6B SDO2A8A TOFA CN3 EM2 (A-axis) M Servo motor CN9 SDI1B+ 2A 2B SDI1BMC Driver Servo amplifier SDO1B+ 3A CN8B CN8 Control circuit 3B SDO1BSTO1 4 STO2 5 CN10 4A SDI2B+ STOCOM 3 4B SDI2BTOFB1 6 2A SRESB+ FG
table. pressure. pressure. emitter. properly, resulting in poor static neutralization. environment, and ions do not reach the object Insufficient amount of blow against amount of due to downflow of the work environment, etc. to the structure Environment Ionized air is not reached because ionized air Potential difference is generated between the Ionized air does not reach the charged object FG
contact (CLOSE During Alarm) 4,5 Unused Alarm Output connector 6 Temperature Alarm a contact (OPEN During Alarm) 7 Temperature Alarm Common 8 Temperature Alarm b contact (CLOSE During Alarm) 9 Unused 1,2 Unused External temperature sensor connector 3 Resistance Bulb Terminal A 4 Resistance Bulb Terminal B D-Sub 15pin (Socket) Fixed screw : M2.6 5 Resistance Bulb Terminal B 6-14 Unused 15 FG
Cover panels of the product should be opened only by qualified service technicians or qualified personnel. 15 FG Circulating fluidWater Circulating fluid flow rate3L/min Facility water flow rate10L/min Wetted materials SUS304 Circulating fluidEthylene glycol 20% Circulating fluid flow rate3L/min Facility water flow rate10L/min 2500 2500 Power supply Single phase AC100 to 240V(+/10%), Single
Functional ground (When the controller is mounted, tighten screws and connect the grounding cable) FG 20 - 3.3 Outside dimension diagram The outside view of this product is as shown in the diagram below: (1) Screw mount type JXC517#-#, JXC617#-# For body mounting (Thread mounting type) (2) DIN rail mount type JXC518#-#, JXC618#-# 167.3 (when DIN rail is locked) 167.3 (when DIN rail is locked
Ensure that the FG terminal is connected to ground when using a commercially available switch-mode power supply. Do not drop, hit or apply excessive shock to the product. Otherwise damage to the internal parts of the product, solenoid valve and internal parts of the pressure switch can occur, causing malfunction.
Be sure to ground terminal FG when using a commercially available switch-mode power supply. Do not drop, hit or apply shock to the Pressure switch. Otherwise damage to the internal parts can result, causing malfunction. Do not pull the lead wire forcefully, not lift the product by pulling the lead wire.
Be sure to ground terminal FG when using a commercially available switch-mode power supply. Do not drop, hit or apply shock to the Pressure switch. Otherwise damage to the internal parts can result, causing malfunction. Do not pull the lead wire forcefully, not lift the product by pulling the lead wire.
Use a protective cover. 15 FG Do not mount the product in a location where it is subject to strong 3.5 Model number of product vibrations and/or shock.