RSH/RS1H Scratches and gouges may damage the packing, causing air leakage or malfunction. CE1 Operation (RSA) CE2 Caution 1. Do not apply external force from the opposite direction to the end lever type locking mechanism when the lever is locked. When pallets move during conveyor adjustment, first lower the cylinder. 2. Be careful in the space between the cylinder and the lever holder.
Note) It may be difficult to replace the cushion seal #4. Note) For wear ring A of 10, please consult with SMC. Seal kit includes a grease pack (10: 5 g and 10 g, 15: 10 g). Order with the following part number when only the grease pack is needed.
9 @0 @1 @2 @3 24 Cylinder tube gasket NBR REAR10-PS 10 REAR10-PS Wear ring A Special resin 10: not available REAR15-PS 15 REAR15-PS Wear ring B Special resin Piston seal NBR Note 1) It may be difficult to replace the cushion seal @3. Note 2) For wear ring A of 10, please consult with SMC. Seal kit includes a grease pack (10: 5 g and 10 g, 15: 10 g).
. @6, @7, @8, @9, #0, #1, #2 Note) REAS15-PS 15 REAS15-PS Wear ring A 10: Not available Special resin Wear ring B Special resin Note) It may be difficult to replace the cushion seal #2. Note) For wear ring A of 10, please consult with SMC. Seal kit includes a grease pack (10: 5 g and 10 g, 15: 10 g). Order with the following part number when only the grease pack is needed.
. @9, #0, #1, #2, #3, #4, #5 @9 #0 #1 #2 #3 #4 #5 Wear ring A Special resin Wear ring B Special resin Note) Cushion seal #5 may be difficult to be replaced. Seal kit includes a grease pack (10 g). Order with the following part number when only the grease pack is needed.
Otherwise, the impact force may exceed the maximum tensile and compressive force of the product, causing breakage. D-X Technical Data 1141
Also, when using in a vacuum, grease may enter the inside due to the nature of its construction. Rotating Torque/Allowable Number of Rotations 5 32 1 4 5 16 3 8 " " " 0.012 8.3 0.014 6.7 0.020 5 Rotating torque (Nm) (2) Allowable number of rotations (S-1) (3) Applicable tubing O.D.
(Reset type) Perform element replacement when the red ring floats up and covers the entire view port. 0.15 0.1 20/24 16 Pressure drop (MPa) 0.05 0.04 w Operation The hydraulic fluid used becomes high viscosity when the temperature is low during the winter, etc., and the differential pressure indicator or the switch may activate.
(Reset type) Perform element replacement when the red ring floats up and covers the entire view port. 0.1 08 10 12 20 24 16 0.05 Pressure drop (MPa) 0.03 w Operation The hydraulic fluid used becomes high viscosity when the temperature is low during the winter, etc., and the differential pressure indicator or the switch may activate.
(Example: If ID60 is connected to a 12 tube, air supply may not be sufficient and it may cause malfunction due to the unstable operation of the check valve. 2. Replace the element of the mist separator, installed on the inlet side, on a regular basis. (Refer to the instruction manual of the mist separator for details such as the replacement interval and procedures.)
Do not disassemble the product because it may damage the air cushion mechanism. Contact SMC when disassembly or maintenance is necessary . 169
The number of stations that may be displayed is longer than the manifold number of stations. Example: -D09 Note 2) When -B is selected, a back pressure check valve is included in all stations of the manifold. If the back pressure check valve is used only for the station that need it, then specify the station location in the manifold specification.
Note) Use caution not to tighten excessively when mounting a pressure gauge, otherwise it may result in a breakdown. For sealing, use a sealant tape.
The warranty period of the product is 1 year in service or 1.5 years after the product is delivered.2) Also, the product may have specified durability, running distance or replacement parts. Please consult your nearest sales branch. 2.
The product specified here may become unsafe if handled incorrectly. The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced. 1.
If the SI unit is not assembled properly, inside PCBs may be damaged or liquid and/or dust may enter into the unit. HOLD ON Hold the last state before communication error. CLEAR OFF Clear all outputs. Configuration In order to configure the SI unit for the EtherNet/IPTM network, the appropriate device master file (EDS file) for the SI unit will be required.
ACR1251U/ACR1252U NFC reader is used. (1): PC/SC Driver (Ver 4.2.8.0 / 2018.3.20) https://www.acs.com.hk/en/products/342/acr1252u-usb-nfc-reader-iii-nfc-forum-certified-reader/ When the NFC reader / writer is held over the product, an error message may appear, such as Device driver software was not successfully installed or Smart card was not identified depending on the version of Windows
When adding new wireless slave unit, it may be required to change the I/O map depending on the wireless channel number. The dummy slave can be registered only with the wireless master unit. Details of dummy slave radio button Description Explanation Insert Button to move the dummy slave to Registered slaves. Input size Set the input size for the dummy slave (0 to 16 byte).
If the SI unit is not assembled properly, inside PCBs may be damaged or liquid and/or dust may enter into the unit. URL http://www.smcworld.com Akihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPAN Phone: +81 3-5207-8249 Fax: +81 3-5298-5362 Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer.
When adding new wireless slave unit, it may be required to change the I/O map depending on the wireless channel number. The dummy slave can be registered only with the wireless master unit. Details of dummy slave radio button Description Explanation Insert Button to move the dummy slave to Registered slaves. Input size Set the input size for the dummy slave (0 to 16 byte).