PF3W7.eng If the valve is adjusted frequently, fluid may leak due to wear of the internal seal.
Specification) The sensor head may be charged depending on potential of the subject. Charging of sensor head may damage the sensor. Caution ! (1) Install the electrostatic sensor apart from the wall(see drawing below). Charged potential may not be measured correctly if walls exist in the range below.
The performance and life may decrease. Also, it may cause danger. 10 XM-OMP0005-A 7-2. Disassembly procedure Step 1 Step 2 Bolt 3 O-ring 1 2 4 Handle assembly Bottom surface of the groove to discharge gas. Body Disassemble the Body and the handle assembly by gradually loosening the hexagon socket head cap screws.
If settings are made by both methods, unintended settings may be configured.
Otherwise, injury or an accident may occur. 5. Do not put hands, etc. in between the air gripper fingers or attachments. Otherwise, injury or an accident may occur. 6. When removing the air gripper, first confirm that no workpieces are being held and then release the compressed air before removing the air gripper.
Retracting failure of the cylinder may occur. Protect the shock absorber from water, cutting oil and dust. Leaving shock absorber unprotected may result in oil leakage and/or general operation failure. Do not scratch or dent the sliding parts of the piston. The piston rod has not been hardened.
It may also result in non-conformity to safety standards. Product handling Installation Do not drop, hit or apply excessive shock to the SI unit. Otherwise damage to the product can result, causing malfunction. Tighten to the specified tightening torque. If the tightening torque is exceeded the mounting screws may be broken.
Leakage may occur if a large rotational force is applied to the housing.
IP65 may not be satisfied depending on the body cover mounting condition.
The operation may become unstable if the product is used with meter-in. Use of a meter-out circuit. Consider the use of a suitable The product shows sudden and fast 1.
Hysteresis may fluctuate due to the operating environments.
Displacement may increase after an impact load has been applied. When the table is subjected to an impact load, there may be permanent distortion of the guide unit and increased displacement.
Note 6) Due to the softness of polyurethane tubing, it may fold when being inserted.
Mounting backwards is dangerous, because the speed adjustment needle will not work and the actuator may lurch suddenly. 7. To adjust the speed, start with the needle in the completely closed position, and then adjust by opening gradually. When the needle valve is opening, the actuator may lurch suddenly creating a dangerous situation.
If handled improperly, damage may occur in machine or equipment or an operational error may result in. 2. Equipment removal and supply/exhaust of compressed air When equipment is removed, first confirm that measures are implemented to prevent dropping of workpiece and runaway of equipment, etc.
Use of tools may cause damage to the product. 2. Check the inlet and outlet pressure indications on the pressure gauge while setting. If the knob is turned to excess, it may cause internal parts to fracture. 3. Since products for 0.02 to 0.2 MPa settings come with a pressure gauge for 0.2 MPa, do not apply pressure exceeding 0.2 MPa. It may cause damage to the pressure gauge.
Never use in the presence of an explosive gas as this may cause a serious explosion. 3. Do not use in an environment where static electricity can cause problems, otherwise system failure or malfunction may result. 1. Do not drop, bump, or apply excessive impacts (980 m/s2) while handling.
Chemical Note 1) Static electricity may be generated. Take measures to prevent static electricity. Note 2) Fluid may permeate through and affect parts made of other materials. 620
(During power saving mode, [ECo] will flash in the sub screen and the operation light is ON (only when the switch is ON).) * There may be a difference in the displayed value on the connected flow switch and the flow monitor.
If the facility water in a cooling tower is used, the water quality standard will be satisfied at the initial stage, however, if it is used in an air contaminated environment, sulfurous acid gas in the air may dissolve into the facility water, forming sulfuric acid which may corrode the electro-thermal surface.