MHS Note 2) When holding a workpiece close at the end of open/close stroke of fingers, detecting performance of the combinations listed in the above table may be limited, depending on the hysteresis of an auto switch, etc. 12-12-12 12-12-13
Note 2) When holding a workpiece close at the end of open/close stroke of fingers, detecting performance of the combinations listed in the above table may be limited, depending on the hysteresis of an auto switch, etc. 12-12-2 12-12-3
Note 2) When holding a workpiece close at the end of open/close stroke of fingers, detecting performance of the combinations listed in the above table may be limited, depending on the hysteresis of an auto switch, etc. 12-12-15 12-12-16
It may cause damage to the element. Be sure to read before handling. Refer to p.0-26 and 0-27 for Safety Instructions and common precautions on the products mentioned in this catalog, and refer to p.4.0-5 to 4.0-7 for more detailed precautions of every series.
Element oil saturation Initial condition Note) Compressed air over max. flow line in the table below may not meet the specifications of the product. It may cause damage to the element. 4.6-9 Micro Mist Separator Series AMD Construction AMD150 to AMD650 AMD850 Component Parts Description Aluminum die cast Aluminum die cast No.
It may cause damage to the element. Flow Characteristics Element initial condition AME150 1/8B AME450 1/2B AME650 1B AME250 1/4B AME550 3/4B AME850 11/2B AME350 3/8B Max. Air Flow How to Select Select the model in accordance with the following procedure taking the inlet pressure and max.air flow into consideration. (Example) Inlet pressure: 0.6MPa Max.air flow capacity: 5m3/min.
Element initial condition Note) Compressed air over max. flow line in the table below may not meet the specifications of the product. It may cause damage to the element. AMF150 1/8B 3/4B AMF550 AMF900/901 2B 1/4B AMF250 AMF650 1B AMF1000 4B 3/8B AMF350 2B AMF800/801 11/2B AMF850 1/2B AMF450 4.6-29 Odor Removal Filter Series AMF Construction AMF150 to AMF650 Component Parts No.
Element oil saturation Initial condition Note) Compressed air over max. flow line in the table below may not meet the specifications of the product. It may cause damage to the element. 4.6-17 Micro Mist Separator with Prefilter Series AMH Construction AMH850 AMH150 to AMH650 Component Parts q Description Aluminum die cast Aluminum die cast Material Note No.
When the work holding point is out of range, the unbalanced load applied to the finger and the guide section may cause excessive play in fingers and have an adverse effect on the gripper life.
Applicable auto switch Notes) Some liquid may make the use of an air gripper or auto switch impossible. Confirm the kind of the questionable liquid and consult SMC for the use.
When the work holding point is out of the limit range, the unbalanced load applied to the finger and the guide section may cause excessive play in fingers and have an adverse effect on the gripper life.
The used of turbine oil at temperatures lower than 0C leads to increased viscosity and may cause the valve to malfunction.
Note) GENTLY pull the lead wire, otherwise it may cause contact failure or disconnection.
If it is mounted in the wrong direction, connected equipment may malfunction. Mount it by referring to how to switch over from N.C. to N.O. specifications. Universal porting permits convertibility N.C./N.O. by a simple 180 degree rotation. Mounting conditions for N.C. and N.O. is indicated as below figure. Valve Exhaust port type N.C. N.O. Common exhaust Caution 1.
Otherwise, air leakage may result. Element Clip Fitting assembly To replace an element, remove the cover on the top side of the end plate and remove the old element with a flat head screwdriver, etc.
The used of turbine oil at temperatures lower than 0C leads to increased viscosity and may cause the valve to malfunction.
If it is pulled off at an angle, the pilot valve may be damaged or the protective O-ring may be scratched. Installation Place the cover straight over the pilot assembly so that the pilot valve is not touched, and push it until the cover hook locks without twisting the protective O-ring. (When pushed in, the hook opens and locks automatically.)
Perform periodic inspections and confirm normal operation, otherwise it may be impossible to guarantee safety due to unexpected malfunction or erroneous operation. 4. Do not touch connector terminals or internal circuit elements when current is being supplied.
If the air flow is allowed outside the range of the rated flow even momentarily, drainage and lubricant may splash at the outlet side or cause damage to the component. 2. Do not use in a low pressure application (such as a blower). F.R.L. unit has its own minimum operating pressure depending on the equipment and is designed specifically to function with compressed air.
Anchoring the head cover or tightening the head cover itself may cause the cover to rotate and slippage to occur. 2. The correct tightening torque for the mounting threads must be within the range shown in the table below. Apply Loctite (No. 242, Blue) to the mounting threads.