Microspeed Cylinder: Double Acting/Single Rod Series CUX ø 10, ø 16, ø 20, ø 25, ø 32 Dimensions and auto switch details are equivalent to those of the standard double acting single rod cylinder. The speed may not be controllable during low speed operation with the meter-out controller. Caution 1. For Series CUX10, up to 0.1Nl/min (ANR) of internal leakage is anticipated due to cylinder structure. 4
When two switches are connected in series, a load may malfunction because the load voltage will decline when in the ON state. The indicator lights will light up if both of the switches are in the ON state.
Brown [Red] When two switches are connected in series, a load may malfunction because the load voltage will decline when in the ON state. The indicator lights will light up if both of the switches are in the ON state.
However, the cable to connect the motor and driver is optional and may be supplied by the customer, or the cable corresponding to the selected motor may be ordered separately by referring to the section on how to order cables on page 10. Stroke (Refer to Table 1 below for applications.)
Caution Use a 3 wire NPN type for each switch. 18 19 20 Caution If input is not provided as prescribed for the operation, this may cause malfunction or failure. 311 Series LC6C Point Movement Home Position Return Operation With this driver, a maximum of 28 point positions can be set by combining banks and points.
Since a regenerative absorbtion unit may be necessary depending on the operating conditions, a separate inquiry should be made.
Mounting on MXP10-10 Suitable mounting position for detection of auto switch / stroke end When MXP10-10 has in-line piping, the auto switch may obstruct speed controller and fitting. Electrical entry from outside Obstruct Speed controller A Auto switch Obstruct A Table of auto switch which obstructs speed controller and fitting Auto switch model no.
Ma = K Mmax Work piece mounting coefficient K: Fig. 3 Allowable moment coefficient : Graph 2 Max. allowable moment Mmax: Table 4 Mar = 36 Mrmax = 36 K = 1 = 1 ' = 0.39/36 = 0.011 May = 1 x 1 x 18=18 Mymax = 18 K = 1 = 1 = 0.39/18 = 0.022 Find the load factor of the static moment.
@ D-90 : lnch D-97 Caution. 1) The abovo dimensions may vary in areas whre magnetic Inlerlerence is present. 2) Fo. 14 stroke cylinder, only one aulo switch may be mounted eithgr on the rod end or the cap end. 3) There are two ways to mounl lhe auto swilches as shown in the above ligure. For B and C method, the cap end auto switch would ertend slightly pastthe cap end.
vvhen installing the positioner on a diaphragm actuator with a diameter of about 8.0 inch (200mm) or less, the gain supffession spring may have to be changed if instability occurs.
Large variations may occur depending on the surrounding environment.
Before piping air, llushing and/orcleaning should be done to completely remove sludge. cutting oil, dust etc. that may exist in the pipe. Before piping and screwing in couplings, please make sure that sludge trom pipe threading and sealing materials do not go into the pipe. When seal tape is used, tape winding should be done so that 2 threads are left untaDed on the end.
Note 1) Use a stainless steel body, as static electricity may be generated. Note 2) Use caution as permeation may occur. Table symbols : Can be used : Depends on conditions X: Cannot be used Compatibility is indicated for fluid temperatures of 100C or less. Consult P/A regarding fluids other than the above. Consult P/A regarding operating conditions. 1.12-6
When two switches are connected in parallel, malfunction may occur because the load voltage will increase when in the OFF state.
At higher temperatures, breakage or flattening, etc., may occur at more than the minimum bending radius.
orientation Unrestricted Vibration/Impact m/s2 Note 4) (ft/s2) 30/150 (9/150ft/s2) Rated voltage 24VDC, 12VDC, 100VAC, 110VAC, 200VAC, 220VAC (50/60Hz) Allowable voltage fluctuation % 10% of rated voltage Coil insulation type Class B Enclosure Note 5) Dust proof (equivalent to IP40) Power consumption W Note 3) 2.5 (VDW10), 3 (VDW20/30) Note 1) Consult P/A when used under conditions which may
When in the exhaust position, the valve may be padlock secured. Prevents accidental start-ups while personnel are cleaning or servicing equipment. The supply/exhaust status of the air flow can be verified at a glance in the indicating window.
Operating pressure 0.5MPa (72.5psi) Withstand pressure 0 to 60C (32 to 140F) (with no freezing) Operating and ambient temperature range 10m Filtration degree Element differential pressure resistance 0.15MPa (21.75psi) Applicable tubing material Nylon, Soft nylon, Polyurethane, Soft polyurethane Symbol Note) Do not use in a line where a pressurized condition is maintained since the body may
Disconnecting the cable during communication may cause a software corruption. 6 - Doc No. LA-OMS0009-B Revision history A: Revised in November 2019 B: Revised in June 2020 The latest Operation Manual can be downloaded from the SMC's website shown below.
Disconnecting the cable during communication may cause a software corruption. 6 - Doc No. LA-OMX0026-A Revision history A: Revised in June 2020 The latest Operation Manual can be downloaded from the SMC's website shown below.