Rotary Actuator NCRB1BW Series Single Vane / Double Shaft (lf lubrication is used, do not discontinue its us.) Olf the kinetic energy oI the load exceeds the permissible range, use external stops to absorb load. O Connect piping atter thoroughly flushing it. O Do not use trydraulic fluid. @Shaft Load lf a static (i.e. non-dynamic) load only is applied to the actuatot it is possible io apply the load values shown in the table below.
As the connected actuator will start operating due to this manual operation, be sure to confirm that it is safe to do so beforehand. Ex. 1) Cable length: 300 mm DXT1215T-5W1U-01m(-X1) Symbol for electrical entry MNon-locking push type Push the manual override button all the way down. 2.
Do not bring objects that are sensitive to magnetism near the cylinder. The magnet is built into the cylinder. Do not bring magnetic disks, cards or tapes near the cylinder. Data may be lost. 5. If the cylinder is operated vertically with heavy loads, measures must be taken to prevent rapid extension of the piston rod when starting to operate in the downward direction.
Do not use it for mounting. Otherwise, the adjustment at shipment may deviate. 792
Do not make any upward angles in drain line.
Do not use this aftercooler in an area that has viscous dust (electrostatic paint powder, oily particles, etc.). If it must be used under such conditions due to unavoidable circumstances, please contact SMC beforehand.
Chromated C3604B Piston C3604B Spring holder Zinc chromate SWP Parallel pin Zinc chromate SWPB Spring SUS304W Valve spring PVC Packing w Do not remove the retaining screw of the handle. If the screw falls off, it could lead to a malfunction.
How to Order Do not replace heavy duty scrapers. XC4 Since heavy duty scrapers are press-fit, do not replace the cover only, but rather the entire rod cover assembly. The CM2 series cannot replace either heavy duty scraper or rod seal. (It goes for replacing retainer assembly for the CS1 series.) Replace the CNA2 series with the lock unit.
Model (Standard) Dimensions Pressure range (1) Connection thread Indication unit Model G15 MPa MPa G15-10-01 (2) R 1/8, M5 (Female thread) 0 to 1.0 0 to 1.0 1 16 G27-10-R1 R MPa Note 1) Do not apply more excessive pressure than max. pressure display. It will be a cause of malfunction.
Because suctioned matter is ejected together with exhaust, do not direct an exhaust port at a person or equipment. AFJ AMV 2.
Do the drain pulling out regularly.
Do not replace the non-rotating guide. Since the non-rotating guide is press fitted, the entire cover assembly needs be replaced instead of a single part. 37
Do not replace the non-rotating guide. Since the non-rotating guide is press fitted, the entire cover assembly needs be replaced instead of a single part. 38
You do not need to specify "N" (i.e., without lead wire) for D-A3A, D-A44A, D-G39A, and D-K39A. This is the only standard specification automatically available for these models.
low speed actuation (no control of cylinder output) Example 2) Low speed with output control Precision restrictors Solenoid valve ITV (Electro-pneumatic regulator) Mist separator (0.01 m or less) (0.3 m or less) Mist separator (0.3 m or less) Air filter (5 m or less) IR (Precision regulator) W Air filter (5 m or less) IR (Precision regulator) W When performing control of cylinder output, do
Do not replace the non-rotating guide. Since the non-rotating guide is press fitted, the entire cover assembly needs be replaced instead of a single part. 37
Do not replace the non-rotating guide. Since the non-rotating guide is press fitted, the entire cover assembly needs be replaced instead of a single part. 38
Do not replace the bushings. The bushings are press-fit. To replace them, they must be replaced together with the cover assembly. 2. To replace a seal, apply grease to the new seal before installing it. If the cylinder is put into operation without applying grease to the seal, it could cause the seal to wear significantly, leading to premature air leakage. 3.
Do not disassemble the power clamp cylinder. The power clamp cylinder consists of a completely sealed structure in order to protect it from welding spatter. Do not disassemble, except for when replacing any of the replaceable parts, as the performance may deteriorate. 10 Power Clamp Cylinder Variations Web Catalog.
VQC4000/5000 series valves do not have common polarity.
② For manifolds with serial transmission kits, whether the valves are positive common or negative common depends on the type of protocol. For VQC1000/2000 series valves, install valves with the same common specification as the common specification of your protocol.