Tie-rod Type Hydraulic Cylinder Note 1) To protect auto switches, ensure that main body of an auto switch should be embedded into auto switch mounting groove with a depth of 15 mm or more. Note 2) Set the tightening torque of a hexagon socket head set screw (M4) to be 1 to 1.2 Nm. Note 3) When tightening an auto switch mounting screw (M2.5), use a watchmakers screwdriver with a grip diameter of 5 to 6 mm.
Therefore, even within a given allowable kinetic energy level, there is an upper limit to the amount of the load that can be sustained. 11.Use a balanced circuit in which lurching of the cylinder is prevented.
Select the point of contact A of inlet pressure and max. air capacity in the graph. 2. AMF650 is obtained when the max. flow line is above the point of intersection A in the graph. HA AT ID Max. air flow rate (m3/min (ANR)) AMG Note) Make sure to select a model that has the maximum flow rate line above the obtained intersecting point.
(mm) ND NN Bore 10 16 A B C D F GA GB H MM NA NB S Z 0 0.022 0 0.022 15 12 14 4 8 8 5 28 M4 X 0.7 12.5 9.5 M8 X 1.0 46 74 75 8 15 18 20 5 8 8 5 28 M5 X 0.8 12.5 9.5 M10 X 1.0 47 10 Refer to p.1.3-8 to 1.3-10 for dimensions of each mounting bracket.
46 F 33 34 34 H 24 25 25 J 30 40 40 D 22 24 24 A 40 44 44 B 20 22 22 C 9 10 10 Model VVX31 VVX32 VVX33 TI/ TIL PA PAX PB 17-3-91
If there is a risk of contact, provide safety measures such as a cover or a system that uses sensors that will activate an emergency stop before contact is made. 2. Use a balance circuit in which lurching of the piston is taken into consideration.
VKF (A) 2 (A) 2 VQZ 1 (P) 3 (R) 1 (P) 3 (R) VZ VS VFN r e w q r e w q N.O. N.O. (A) 2 (A) 2 1 (P) 3 (R) 1 (P) 3 (R) Component Parts Description Material Note No.
Note) The -X126 model cannot be manufactured with an L plug connector for electrical entry. Therefore, use a grommet type or an M plug connector.
Load is an analog input equipment such as a voltmeter.
B 2 A 4 VQZ 5 SMC SMC SMC SMC SMC B A VQD B 2 A 4 4 B A P = 41 L1 L2 B 2 A 4 3 B A B 2 A 4 2 B A 34.5 46 68.5 P = 41 A 4 B 2 1 B A 58.5 X 12 Stations 2-Rc 1/8 (External pilot port) 15.5 22 51 69 117 42 16 107.8 179 D side With connector on D side (FD) Formula: L1 = 41n + 76, L2 = 41n + 96 n: Stations (Maximum 12 stations) Dimensions L n 12 568 588 L1 L2 11 527 547 10 486 506 9 445 465 8
Note 5) Air is normally being discharged to the atmosphere from a bleed hole or an exhaust port.
Unpacking the sealed package Since the filter and element are sealed in an antistatic double bag, the inner package should be unpacked in a clean atmosphere (such as a clean room). 316
If a problem is detected by one or both external switches, an alarm is generated and the operation stops. You can set the product to continue operation or not to detect the alarm.
Refer to page 17-3-65 for ordering a coil only.
igs 3 wiE slslem lwhen Dower source lor slrlbh and load is commod) Contact capacity a Loads overthe minimum contactcapacity of the switch should not be used. I t r i : : O _ _ a r ! P ! ! : o : L o a d F = I Ll|acxo re 3 riire syslom (Wren pol9l sqJme lor swioh and load s nol cofimom) Fled ^ | | ,.,",.-" a-a ao | | :".'*: ' "l Load l *lrlii + | | t r a ! ! !
igs 3 wiE slslem lwhen Dower source lor slrlbh and load is commod) Contact capacity a Loads overthe minimum contactcapacity of the switch should not be used. I t r i : : O _ _ a r ! P ! ! : o : L o a d F = I Ll|acxo re 3 riire syslom (Wren pol9l sqJme lor swioh and load s nol cofimom) Fled ^ | | ,.,",.-" a-a ao | | :".'*: ' "l Load l *lrlii + | | t r a ! ! !
Warning (1) The port marked with an arrow () is the 1 (P) port (IN) and one on the opposite side is the 2 (A) port (OUT). The port at a right angle to them is the 3 (R) port (EXH).
When the stroke adjustment unit is fixed in an intermediate position, slippage can occur depending on the amount of energy released at the time of an impact. In that case, use a short spacer or a long spacer. For other lengths, please consult with SMC. (Refer to Tightening Torque for Stroke Adjustment Unit Holding Bolts.)
If a problem is detected by one or both external switches, an alarm is generated and the operation stops. You can set the product to continue operation or not to detect the alarm.
VQZ (A) 2 (A) 2 VZ 3 (R) 1 (P) 3 (R) 1 (P) VS VFN r e w q r e w q N.O. N.O. (A) 2 (A) 2 3 (R) 1 (P) 3 (R) 1 (P) Component Parts No.