Mechanically Jointed Rodless Cylinder with Brake, Hy-rodless Cylinder Series ML1C ø25, ø32, ø40 1 The unit body can be fixed by tightening four holding bolts evenly at an arbitrary position. However, there is a possibility that the adjustment mechanism will be tilted due to high impact energy. Since the holder mounting bracket for adjustment is available as an option for -X416, X417, we recommend that you use it.
An application which could have negative effects on people, property, or animals requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation. 1.
An application which could have negative effects on people, property, or animals requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation. 1.
An application which could have negative effects on people, property, or animals requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation. 1.
An application which could have negative effects on people, property, or animals requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation. 1. The product is provided for use in manufacturing industries.
The unit body can be fixed by tightening four holding bolts evenly at an arbitrary position. However, there is a possibility that the adjustment mechanism will be tilted due to high impact energy. Since the holder mounting bracket for adjustment is available as an option for -X416, X417, we recommend that you use it.
Install an air dryer or after cooler on the upstream side of the pressure release 3 port valve because air containing excessive drainage may cause malfunction. SA VA SA Model VHS20 VHS30 Effective sectional area (mm2) (Cv) 5 (0.27) 5 (0.27) Caution VA 3. Do not apply negative pressure. It may result in malfunction. 1. Install an air filter of 5 mm filtration on the inlet side. 2.
They do not guarantee an actual fixed range (expect approximately 30% dispersion).
Then, give an additional half rotation of screw. After that, incline the lever by 90 and confirm that the indicator light is not on and does not show either red or green.
This clears the unit when an abnormality occurs and clears the accumulated flow display to "0". UP Button ( Button) U P Output (OUT1) Indicator/Green Use when increasing a setting value. SET Lights up when OUT1 is ON. It also blinks when an overcurrent error occurs on OUT1. OUT2 OUT1 SET Button ( Button) DOWN Use when changing a setting value or any of the modes.
For the external pilot valve, an R should be attached to the valve and the manifold part number. (See the below.)
Inch Example: 25 = 0.25 (1/4) Inch Stroke Specify XI Dimension in inches Construction Type S T Y L E Pneumatic H Hydraulic S TA N D A R D S T R O K E O P T I O N O V E R S I Z E D R O D XB5 O P T I O N Inches Example: 04 = 4 Stroke When ordering an oversized rod, please order the following way to represent the rod size required.
The drain pipe must have a minimum pipe bore of 10 mm, and a maximum length of 5 m (when installing an optional auto-drain).
If the piston impacts the stroke end with excessive kinetic energy (values in Table 1 or more), an excessive impact will occur and this may cause damage to equipment. Table (1) Allowable Kinetic Energy At Piston Impact Unit: [J] Allowable kinetic energy 50 to 500mm/s 20 25 32 40 50 63 80 100 Piston speed 0.055 0.09 0.15 0.26 0.46 0.77 1.30 2.27 7-7-19
The cushion effect (smooth start-up, soft stop) cannot be obtained in an intermediate stop or return from an intermediate stop using an external stopper, etc. When using an intermediate stop considering the above information, implement measures to prevent particulate generation and set the operating pressure to no more than 0.3 MPa.
A 0.6 16 Do not operate with the stroke adjusting unit fixed in an intermediate position. When the stroke adjusting unit is fixed in an intermediate position, slippage can occur depending on the amount of energy released at the time of an impact. In such cases, the use of the adjusting bolt mounting brackets, available per made-toorder specifications -X416 and -X417, is recommended.
An application which could have negative effects on people, property, or animals requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation. 1.
Make sure to perform a periodic inspection of the pressure gauge when it is used by installing it between a solenoid valve and an actuator, etc. Sudden pressure changes could happen and the durability of the product could be reduced.
Type of actuation C (dm3/(sbar)) b Cv C (dm3/(sbar)) b 1 4/2 (P A/B) 4/2 5/3 (A/B EA/EB) Cv P, EA, EB A, B 35 37 Single Double 2 position 0.44 0.61 0.16 0.64 0.45 0.18 0.46 0.13 0.47 0.43 0.48 0.13 Closed center Exhaust center Pressure center SA SYA320-M5 M5 x 0.8 0.42 0.47 0.13 0.47 (0.44) 0.41 (0.37) 0.13 (0.12) 3 position 39 VA 0.50 (0.41) 0.48 (0.35) 0.15 (0.11) 0.47 0.43 0.13 44 46
Secure the switch at an appropriate position with a flat head watchmakers screwdriver as indicated in Figure 3. Tightening torque: 0.05 to 0.1 Nm Second groove MRHQ 10, 16 3. Install the switch case, with a switch attached securely in the hole, in the direction indicated in Figure 1.