IZx-OMX0087 At the positive ion adjustment limit, the LED at the end of the positive side (right end of the display) flashes (orange). At the negative ion adjustment limit, the LED at the end of the negative side (left end of the display) flashes (orange). For highly precise offset voltage adjustment, adjust the ions generated by the ionizer by monitoring with a charge plate monitor.
Add X416 and X417 at the end of part No. of unit. Ex. MY-A25L-X416 3) When ordering holder mounting bracket only. Add N at the end of part No. of unit. Ex.
o 85% RH lor lmin between and 50Mti or more (at belween bad wires and body In X. Y, Z directions 3limes each 12.6FS or lesis at 25'C 01: Rl/8. [.r5 x 0 8, Tl: NPT1/8, M5 x 0 8.
o 85% RH lor lmin between and 50Mti or more (at belween bad wires and body In X. Y, Z directions 3limes each 12.6FS or lesis at 25'C 01: Rl/8. [.r5 x 0 8, Tl: NPT1/8, M5 x 0 8.
(The cable insulator must be stripped at 3/8inch (10mm).) 4. Insert the cable and remove the screwdriver. 5.
[1] Power supply input terminals, L1, L2: Provide specified power supply to input terminals L1 and L2. [2] Connect the motor input terminal (U, V, W) to the driver power terminal (U, V, W).
7) 0V [1] Power supply input terminals, L1 and L2: Specify power supply to input terminals L1 and L2. [2] Connect the motor power supply input terminal (U, V, W) to the driver power terminal (U, V, W).
Allow at least 0.5 second from a locked stop (intermediate stop of the cylinder) until release of the lock. When the locked stop time is too short, the piston rod (and load) may lurch at a speed greater than the control speed of the speed controller. 5.
Pullthe valve up at the front.
Signal output At start: Closed At stop: Open (Including Failure): Open 1. Operation signal 2. Failure signal Protective equipment in operation: Closed Protective equipment not in operation: Open If the product is stopped by the overload relay built into the compressor, the Failure signal will not be output.
Spatter Cover 2: KR (Applicable tube: FR soft nylon, FR double layer) Applicable fitting size Model Installed L1 L2 D KR-08C1 KR-06C1 6 12.8 15 18 20 KR-10C1 KR-12C1 18 13.7 20 15.7 22 17.2 22 17.2 8 10 12 One-touch fitting How to install One-touch fitting Construction of spatter cover Install with matching A and B parts. 15-3-5
Since CSA is a test certifying body as the National Recognized Testing Laboratory (NRTL) within the jurisdiction of Occupational Safety and Health Administration (OSHA), SMC was tested for compliance with CSA Standards and UL Standards at the same time and was approved for compliance with the two Standards.
Dimensions n L 2 39 31 3 50 42 4 61 53 5 72 64 6 83 75 7 94 86 8 105 97 9 116 108 10 127 119 11 138 130 12 149 141 13 160 152 14 171 163 15 182 174 16 193 185 17 204 196 18 215 207 19 226 218 20 237 229 L1 L2 1.13-11
K P. 60 KCH P. 69 KCL Use to pipe at right angles to female thread. M H D Union tee Elbow plug for frequent use It can save tube cutting labor in the case of frequent tube installation and removal. Use to connect a self-seal fitting and a tube at the right angles to a self-seal fitting. P. 61 KCL P. 69 KCT MS Use to connect tubes in both 90 directions.
(Coil temperature: 20C, pressure: 0.5 MPa, at rated voltage, with light and surge suppressor, value at operation excluding restart period) The period immediately after a restart may be delayed for about 1 msec depending on operating conditions. Note 2) Use dry air to prevent condensation when operating at low temperatures.
(at 80 mA load current) PNP: 1.5 V max. (at 80 mA load current) Response time 25 0.5 s/1 s/2 s Output protection Short circuit protection Flow Selects one of the output (hysteresis or window comparator mode), the output for the accumulated flow and the accumulated pulse output. Output mode Temp. Selects the output for fluid temp.
A horizontally mounted cylinder should also be operated with a load mass less than the ranges given in the graph at left.
CAUTION During the dryer operation, keep the ball valve open at all times. When the ball valve is closed, the condensate drain cannot be discharged. Keep the drain cock at S side. If the drain cock is at O side, compressed air continues to bleed.
(at 500 VDC) between terminals and case Standards CE/UKCA marked, UL (CSA) -21No.PF-OMJ0016-J Specifications of piping port Model 01 02 N01 N02 F01 F02 C4 C6 C8 N7 4 8 6 1/4 (5/32") (5/16") Thread type (Port size) Rc Rc NPT NPT G G OneOneOneOne1/8 1/4 1/8 1/4 1/8 1/4 touch fitting touch fitting touch fitting touch fitting Straight without flow adjustment valve 95 g 125 g 55 g Bottom entry
With pressure at rod cover port Low friction side CB (Example of application q) With pressure at head cover port Low friction side CA (Example of application w) In both cases, as long as the outside pressure moves the piston rod, low friction can result in the direction of extension and retraction.