Direct Operated the following formula which is based on the test conducted by the test circuit analogous to ISO 6358.
The display End will be replaced by 0.0, leading to the input STEP 1. Input first setting position into STEP 1. Then, press WRITE to proceed to STEP 2. Set the following setting positions, STEP by STEP . After inputting the last data into last STEP , press WRITE, and then END to end the program setting.
Then it is cooled to the specified temperature by the air cooler using the evaporation heat of refrigerant. At this time, the moisture generated by condensation are automatically exhausted by the auto drain. The cooled and heat is exchanged with hot air that flows into the air re-heater. It is supplied as dry warm air without "sweatuing" in the pipimg system.
In addition, when atmospheric pressure is desired, shut off the power after reducing the set pressure, and then introduce atmospheric pressure by using a vacuum release valve, etc. i If the power for this product is cut off by a power failure, etc. when it is in a controlled state, the setting side pressure will be held temporarily.
Products approved by CSA or UL standards are accepted in most states and governments beyond question.
Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires. This may not only cause broken lead wires, but it may cause internal elements of the switch to be damaged by the stress. 3. Mount switches using the proper tightening torque. When a switch is tightened beyond the range of tightening torque, the mounting screws or switch may be damaged.
Universal male elbow Male run tee Bulkhead union Universal male elbow allows thread connection by using a socket wrench for confined spaces. Use to branch line in the same direction from female thread and in 90 direction. KRY P. 4 KRV KRE P. 5 P. 3 Use to connect tubes through a panel.
/N.O. type can be switched by supplying air to port 1(P) or 3(R). 2 way valves and selector valves can also be freely used. Type 40 Easy manual operation Since manual overrides are located in 2 directions, on the top and on the side of the valve, manual override operation is possible unaffected by mounting space and piping direction, etc.
Note 3) Intermediate stroke is available by the 1 mm interval.
The air pressure that flows in acts on diaphragm C and while opposing the force generated by diaphragm B it also acts on diaphragm A opposing the compression force of the setting spring and becomes the set pressure.
Products approved by CSA or UL standards are accepted in most states and governments beyond question.
Series VVXA21/22 Dimensions/Manifold Common SUP type IN port Pilot port Blanking plate OUT port (Pitch) (Pitch) Individual SUP type OUT port Pilot port Blanking plate IN port L Dimension Pitch Pitch Model Stations 2 3 4 5 6 7 8 9 10 Symbol L1 L2 L1 L2 100 86 126 108 136 122 172 154 172 158 218 200 208 194 264 246 244 230 310 292 280 266 356 338 316 302 402 384 352 338 448 430 388 374 494
Order Made Power Saver Power consumption is decreased by 1/3 of standard product by reducing electrical power at holding. (This is effective when energizing time exceeds 62ms at rated voltage of 24V DC.) Specifications Operating principle 1 2 3 4 1 2 3 4 SY1 T SY1 AT SY Series Power consumption at holding is decreased with the below indicated circuit, for energy savings.
Note 2) Cylinder speed of CJ2 and CM2 is limited by the fixed orifice built-in. Note 3) Cylinder speed: when the cylinder is extended.
357 253.5 L2 81 322.5 127.5 196.5 300 162 231 369 265.5 L3 93 334.5 115.5 192.5 308 154 231 385 269.5 L1 77 346.5 VV2CS3 127.5 204.5 320 166 243 397 281.5 L2 89 358.5 139.5 216.5 332 178 255 409 293.5 L3 101 370.5 124.5 207.5 332 166 249 415 290.5 L1 83 373.5 VV2CS4 136.5 219.5 344 178 261 427 302.5 L2 95 385.5 148.5 231.5 356 190 273 439 314.5 L3 107 397.5 Manifold composition 3 stns. x
Surge voltage A high voltage which is momentarily generated in the shut-off unit by shutting off the power.
Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires. This may not only cause broken lead wires, but it may cause internal elements of the switch to be damaged by the stress. 3. Mount switches using the proper tightening torque. When a switch is tightened beyond the range of tightening torque, the mounting screws, or switch may be damaged.
The port A pressure is fed back to the control circuit by the pressure sensor.
Add and increase the attached tie-rod (2 pcs. per block) to the increased block respectively and pass through a block by the tie-rod. 4.
Finger motion is synchronized by a rack and pinion mechanism.