SFOD-OMT0011CN BUSY OFF 27 No.SFOD-OMT0011CN-A 4.2 (1) a) View(V) 4.1 (1-1-2) View (V) Actuator selection b) b-1) conditions Model Motor mounting Lead Stroke 28 No.SFOD-OMT0011CN-A b-2) Search from Part No.
When a 3 port valve is mounted on a 5 port manifold, The "A" port is the working port. The "B"port can either be plugged or unplugged.
A Parts list Section A enlarged view Description Material Note No.
Dimensions with dashed lines stand for a locking knob type or push-locking knob type (latching type). 13 Series VQ100 Non Plug-in Subplate Mounted Valves VQ110-G-M5 28 Manual override 4.9 4.9 12.4 15 E 2-2.7Mounting hole 12 17 2.5 (Lead wire length) About 300 In case of locking knob type SMC SMC VQ110 G 30.7 28 11 7 JAPAN A P (5.9) 5 (5.9) 5 5 (4.1) 4.9 3-M5, (M3) 4.9 8.5 (28) ( ) : In
Nominal size (Torque) For 1 piece, a right hand auto switch is installed.
P/A as a contact protection box may be necessary.
A A A A A Speed Home position A B C Speed no. Time Two pattern combination example (A five point movement of absolute move A and incremental move B) Acceleration no.
Devise a safe system so that if a person engages the emergency stop or if a safety device is tripped during a system malfunction,such as a power outage, the operation of the magnet gripper will not cause a hazard to humans or damage the equipment. 7. Consider the action when operation is restarted after an emergency or abnormal stop.
With this driver, a maximum of 28 point positions can be set by combining banks and points.
Remove a housing from a body by rotating 4 mounting screws counterclockwise with a hexagon wrench key. Hexagon wrench key Nominal: 5 2) Remove the valve guide. Hold the valve guide with a spanner on the spanner flat to rotate it counterclockwise and remove the valve guide. Spanner Nominal: 30 3) Remove the valve spring. 4) Remove the valve assembly.
Remove a housing from a body by rotating 4 mounting screws counterclockwise with a hexagon wrench key. Hexagon wrench key Nominal: 5 2) Remove the valve guide. Hold the valve guide with a spanner on the spanner flat to rotate it counterclockwise and remove the valve guide. Spanner Nominal: 30 3) Remove the valve spring. 4) Remove the valve assembly.
Blanking block assembly (VCA30, 40) VVCA 3 0 2A 00 3 4 Series VCA30 Series VCA40 This is used when a blanking block is mounted on a manifold as preparation for a planned valve installation.
Refer to page 1137 for details. 28 Auto Switch Mounting MXH Series Auto Switch Mounting Watchmakers screwdriver MXH MXH Auto switch mounting screw MXS MXQ When tightening the auto switch mounting screw, use a watchmakers screwdriver with a handle 5 to 6 mm in diameter.
A y OUT 2 I N 1 SMC A t e IN OUT r q w Parts list Material Note Description No.
Do not use a stopper cylinder for intermediate stopping of loads directly connected to a cylinder, etc. The operating ranges shown in the catalog should only be used for stopping pallets on a conveyor. If loads connected directly to a cylinder, etc., are stopped with a stopper cylinder, the cylinder's thrust will become a lateral load. Please consult with SMC in this case. Danger 1.
A model should be selected with a holding force of 10 to 20 times that of the component weight. If high accelleration, decelleration or impact forces are encountered during motion a further margin of safety should be considered.
Do not use a stopper cylinder for intermediate stopping of loads directly connected to a cylinder, etc. The operating ranges shown in the catalog should only be used for stopping pallets on a conveyor. If loads connected directly to a cylinder, etc., are stopped with a stopper cylinder, the cylinder's thrust will become a lateral load. Please consult with SMC in this case. Danger 1.
A model should be selected with a gripping force of 7 to 14 times that of the component weight. If high acceleration, deceleration or impact forces are encountered during motion, a further margin of safety should be considered.
Standard Base mounted Universal External pilot Flow Characteristics/Weight Flow characteristics (1) Port size Valve model Weight (kg) Series 2 1 (A P) 1 2 (P A) 3 2 (R A) 2 3 (A R) C [dm3/(sbar)] 3.3 4.0 2.9/2.9 3.1/2.9 6.6 9.1 6.5/7.0 7.9/8.1 12 15 12/12 15/14 Cv 0.86 0.99 0.74/0.76 0.79/0.83 1.6 2.4 1.7/1.8 1.8/1.9 2.9 3.8 2.9/3.1 3.5/3.3 C [dm3/(sbar)] 3.4 3.7 3.3/3.6 4.1/4.1
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.