SI unit for EtherNet/IP TM NOTE D class grounding (with the ground resistance of 100 ohm or less) should be performed for ground terminal, and ground at one point. -13No.EX-OMK0004-B Pin layout and connection diagram of power supply connector cable (unit: mm) Model No.: EX500-AP-S (Refer to page 31.) Pin No.
SI unit for SY/VQC/S0700 series valves (EX500-Q01) (EX500-Q02) -32No.EX##-OMO0019 Input Unit Manifold Model indication and How to order -33No.EX##-OMO0019 Summary of Product parts The Input unit manifold consists of Input unit, input block (s), end block and DIN rail. The input block up to 8 can be connected (16 points).
Mount the marker (EX600-ZT1) into the marker groove as required. -17No.EX-OMN0028-B SI unit Model Indication and How to Order EX600-S A SI Unit Polarity of output Symbol Content Protocol 1 PNP(-COM.) Symbol Content 2 NPN(+COM.) PR PROFIBUS DP Summary of Product parts No.
Explanation of screen a) Error log number b) Manifold number/Unit number (Refer to page 16) c) Channel number d) Displayed unit symbol (Refer to page 52) e) The next error log is displayed with the and buttons. f) h: hour, m: minute, s: second The time elapsed from when the power supply was applied until the time when error was generated is displayed.
Recommended tightening torque Unit: N m Thread size 1/8 1/4 3/8 1/2 3/4 Torque 7 to 9 12 to 14 22 to 24 28 to 30 28 to 30 (4) Before using an SMC fitting and S coupler, please refer to "Tightening the threaded portion of the connection thread" of the Fittings & Tubing Precautions. (5) Do not apply torsion or bending moment other than the weight of the product itself.
May S TS US VS . ZS AS BS . This function raises an alarm when temperature of the circulating fluid is out of allowable upper and lower range. When the alarm is raised, WRN is indicated on LCD. If circulating fluid temperature returns to within allowable upper/ lower range, this alarm is automatically cancelled.
Bore size 4 6 10 16 Allowable Kinetic Energy(J) 0.7510 1.210 -2 2.510 -2 5.010 -2 -2 (Supply pressureat P=0.7MPa) 10 16 10 1 Load weight (kg) 4 6 0.1 0.01 10 100 1000 Maximum drive speed (mm/s) 18 Lateral Load at Rod End Caution In principle, the load applied to the piston rod should always be kept in the axial direction.
Type Optical linear encoder (incremental) Resolution [ m] 30 1.25 30 1.25 30 1.25 5 1.25 Sensor Origin position signal None Provided None Provided None Provided Provided Pushing speed [mm/s] 6 Pushing operation Set value of force Note 1) Note 2) Note 3) 1 to 5 1 to 4.8 1 to 3.9 1 to 2 Positioning resolution [ m] 30 1.25 30 1.25 30 1.25 5 1.25 Positioning operation Positioning repeatability
Before using an SMC fitting and S coupler, please refer to "Tightening the threaded portion of the connection thread" of the Fittings & Tubing Precautions. Drain guide is not equipped with valve function. Be sure to connect piping for drain. No piping for drain allows the drain and compressed air to exhaust freely.
.: GR-S-010 (10 g), GR-S-020 (20 g) 103
.: GR-S-010 (10 g) , GR-S-020 (20 g) 104
Grease pack part no.: GR-S-010 (10 g) 63
Series 10-MGF Guide table 40, 63, 100 How to Order 10 M G F 63 50 Y59B Number of auto switches 2 pcs. 1 pc. 10 Clean series Relief type Nil S Bore size (mm) Reed switch Type of auto switch Port type Z73 Solid state switch Y59A,Y59B Bore size Type Rc NPT G Symbol Nil TN TF 40, 63, 100 Cylinder stroke (mm) Model Cushion Bore size (mm) 40 63 100 Standard stroke (mm) Auto switch mounting Action
NIL S Nominal size 10 15 Connecting port E: Axial side R: Body side Port Port Applicable Auto Switches/Refer to pages 797 to 850 for further information on auto switches.
D 32 MHT2 F9BW S The toggle mechanism holds workpiece even when pressure drops. Toggle type air gripper Number of auto switches Auto switch Without auto switch (Built-in magnet) Nil Nil Number of fingers 2 pcs. 1 pc. S n pcs. n 2 fingers 2 Auto switch is attachable. For the applicable auto switch model, refer to the table below.
(Initial conditions) 200 0.05 32 SFE1 SFE3 Inlet pressure/Back pressure [MPa] 150 SFE5 0.04 25 100 SFE4 SFE7 95 20 0.03 50 10 0 0.02 0 100 200 300 400 500 600 700 800 Cylinder driving speed [mm/s] AN 0.01 AMC Example) Bore size: 32, Driving speed: 400 mm/s, Supply pressure: 0.5 MPaG 1. From the graph, exhaust flow rate is found to be 95 L/min (ANR). 2.
Basic Axial foot Front flange Rear flange Single clevis Double clevis Front trunnion T E BZ B L F G C D U CJ2 F Low friction direction Boss-cut front flange FZ CM2 Side at pressure When pressurized on head side Boss-cut front trunnion B Side at pressure When pressurized on rod side UZ C85 CG1 L 40 150 CM2Q F Standard MB C95 CDM2Q L F 40 C73 150 With auto switch CA1 Number of auto switches S
Air Cylinder/Low Friction Series CS1lQ Non-lube/125, 140, 160 How to Order Standard L Q 160 300 JR CS1 160 A53 L Q 300 JR CDS1 With auto switch Number of auto switches 2 1 3 n S 3 n With auto switch Mounting Basic Foot Front flange Rear flange Single clevis Double clevis Center clevis B L F G C D T Auto switch Low friction Without auto switch * Select the applicable auto switch from the
Calculation for speed and pulse frequencies Pulse frequency [pps] = (Speed [mm/s]/Lead [mm]) x Divisions per rotation Calculation for moving distance and pulse numbers Pulse numbers = (Moving distance [mm]/Lead [mm]) x Divisions per rotation LJ1 LG1 LC1 LX LC6D/LC6C Switches The divisions per rotation are as shown in the table below.
NPT thread Model Model 10-32 UNF M5 3/8 1/8 1/4 1/2 3/8 1/8 1/4 1/2 AKH04 AKH06 AKH08 AKH10 AKH12 AKH03 AKH07 AKH09 AKH11 AKH13 4 6 8 10 12 5/32 1/4 5/16 3/8 1/2 From One-touch fitting to male thread B Bushing type AKB 01 A 01 S With seal (Standard) Body size Port size 01 1/8 01 1/8 Thread type 02 1/4 02 1/4 03 3/8 Nil R 03 3/8 04 1/2 N NPT 04 1/2 Check valve free flow direction Female/Male