Fieldbus system (DeviceNet compliant) It may also result in non-conformity to safety standards. Product handling Installation Do not drop, hit or apply excessive shock to the fieldbus system. Otherwise damage to the product can result, causing malfunction. Tighten to the specified tightening torque. If the tightening torque is exceeded the mounting screws may be broken.
Check wiring Incorrect wiring may cause damage or malfunction of the products. Make sure the wiring is correct before operation. 6. Wiring arrangement and fixation Avoid bending cables sharply at connector part or electrical entry in wiring arrangement. Inproper arrangement may cause disconnection which in turn causes malfunction.
Inadequate differential pressure may increase the bleed amount from the bleed hole because of the wearing of internal part. This may effect on the performance. 3.
ground lines to piping, as this may cause electric corrosion of the system. (3) Mounting of fitting Tighten the fitting as follows: After tightening, confirm there is no leakage from the fitting.
This may damage the product, as well as, decrease its performance and life expectancy. Do not disassemble the parts that are not explained in this operation manual. This may decrease the performance and life expectancy of these parts. In addition, disassembly may cause danger. Torque values specified in this manual must be followed.
Use caution, because an external action such as an impacting load, strong vibration or turning force, may damage the locking mechanism or reduce its life. 2. Consider stopping accuracy and the amount of over-run when an intermediate stop is performed.
The period may vary depending on the temperature and other conditions. In some cases the absorber may need to be replaced before the allowable operating cycle above.
When the finger opening/closing speed is set as the total stroke of 0.2 seconds or more, it may cause the product to stick or completely stop its movement. Made to Order (Refer to pages 683 to 713 for details.)
The flatness of the mounting face may deteriorate, the guide's deviation range may increase and the sliding resistance may become greater. Do not allow hands or fingers near the cylinder during its operation. Your fingers may be caught between the body and the plate. If you need to come near the cylinder during its operation, install a cover on the cylinder.
Use caution, because an external action such as an impacting load, strong vibration or turning force, may damage the locking mechanism or reduce its life. 2. Consider stopping accuracy and the amount of over-run when an intermediate stop is performed.
It may vary substantially depending on an ambient environment.
If the oulet side capacity is undersized, pulsation may occur.
It may cause a malfunction or damage. 2. Wiring of ZSM1-121 Switches may be connected in series, voltage drop will be increased by the LEDs internal resistance (2 V drop per each). Use switches within the specified range of min. operating voltage. 3. Diaphragm switches have no built-in contact protection circuits. Use switches with contact protection box (part no.
(mm) The standard chamfer may not be altered depending on the type of machining required.
When valve starts its operation, the gate may cut off fingers etc. (4) Please dont remove the side plates on actuating part. Touching moving part with hands during operation may cause injury. (5) Please exhaust all pressure in cylinder with disconnecting air piping on operating part at valve maintenance. Warning B 4-7Replacement of O-ring Use the parts designated on 5.
If operated beyond the limiting ranges, this may cause the equipment life to be reduced or damage to equipment may occur. Lateral load Eccentric distance Stroke Selection Caution Graph (2) 100 1. Operate the cylinder to the stroke end. When the stroke is restricted by an external stopper or a clamped work piece, satisfactory cushioning and noise reduction may not be achieved. 2.
be generated from loading equipment with a large capacity (power consumption), and the solenoid valve in a deenergized state may switch over (see Figure 1).
The product specified here may become unsafe if handled incorrectly. The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced. 3.
The product specified here may become unsafe if handled incorrectly. The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced. 3.
Check the dimensions to select the correct product size, as a fitting may interfere with the product and it may not be possible to mount the product when it is mounted to a tube connection port of a solenoid valve, etc. 1.