Pressure Sensor There may be an error in the output voltage depending on this output impedance and the input impedance of customers' equipment.
However, depending on the number of switches in the ON state, the indicator lights may sometimes dim or not light up, because of dispersion and reduction of the current flowing to the switches.
OR connection / / + + In case of AND connection of two 2-wire type switches, load malfunction may be caused by the load voltage decrease when turned ON. The indicator light comes on when the two switches are turned ON. In case of OR connection of two 2-wire types switches, load malfunction may be caused by the load voltage increase when turned OFF.
All 6ther options are available, whereas they may be stocked in lesser quantities or manufactured to order. Special arrangements can be made for repeating (blanket) orders of these product models.
The dither may generate vibrations in fe valve which produces a growling noise and may be ad.iusted within a range of 100 to 2m Hz by luming the DITHER adiustment screw.
Operation outside of this range may cause excessive impact, which may result in the damage to the devices.
Countermeasures for static electricity Since static electricity may be generated depending on the fluid being used, implement suitable countermeasures.
If a slide bearing is used, sliding resistance increases due to the load mass and moment, which may cause malfunctions. When the cylinder is mounted vertically or sidelong, a slider may move downwards due to the selfweight or workpiece mass. If an accurate stopping position is required at the stroke end or midstroke, use an external stopper to secure accurate positioning.
The product may not be suitable for use with specific gases and applications/environments. Check the compatibility of the product materials with the process gas. Design the equipment and select the product by understanding the characteristics of gas. 2. Confirm allowable pressure of any pressure gauges.
Use caution the piston rod may be lurched when the next motion gets started after the intermediate stops or commence the operation after the reverse motion gets done, unless the air balance is taken. It may result in degrading its accuracy.
About 10% error may occur due to the difference in tolerance of the power clamp cylinder body. D) Under the state described in step C, adjust shim w so there is contact between the clamping block and the workpiece.
Furthermore, when replacing mounting brackets, the unit holding tie-rods may get loosen. Tighten them once again in such a case. Use socket wrench for replacing the mounting bracket or tightening tie-rod for unit mounting. CL CL1 MLGC CNG 2.
CRB2 (mm) E1= E3= The standard chamfer may not be altered depending on the type of machining required.
If it is pulled off at an angle, the pilot valve may be damaged or the protective O-ring may be scratched. Installation Place the cover straight over the pilot assembly so that the pilot valve is not touched,and push it until the cover hook locks without twisting the protective O-ring. (When pushed in, the hook opens and locks automatically.)
If the piping diameter is reduced, it may lead to insufficient flow of supply air, reduction of suction flow and reduction in the vacuum pressure. 1 The values indicating characteristics are representative values, and may vary depending on the atmospheric pressure (weather, altitude, etc.). 2 Supply pressure: 0.45 MPa Construction Model Selection Caution q t w r e y 1.
Use caution the piston rod may be lurched when the next motion gets started after the intermediate stops or commence the operation after the reverse motion gets done, unless the air balance is taken. It may result in degrading its accuracy.
(If an excessive force is applied in the rotary direction, it may bring about the damage to the internal mechanism.) Refer to the following table for the tightening torque for mounting.
If it uses turbine oil in place of fluids for cylinder, it may result in oil leakage. 5. Combine the rod end section, so that a rod boot might not be twisted. If a rod boot is installed with being twisted when installing a cylinder, it will cause a rod boot to fail during operation.
Operation outside of this range may cause excessive impact, which may result in the damage to the devise. Make sure to operate strictly within the allowable lateral load range to the plate. Operation outside of this range may result in shorter service life or damage to the devise.
If operated beyond the limiting ranges, this may cause the equipment life to be reduced or damage to equipment may occur.