CNA Furthermore, when replacing mounting brackets, the unit holding tie-rods may get loosen. Tighten them once again in such a case. Use socket wrench for replacing the mounting bracket or tightening tie-rod for unit mounting. CL CL1 MLGC CNG 2.
If the signal is delayed, the piston rod (and load) may lurch at a speed greater than the control speed of the speed controller. 6.
Use caution, because an external action such as an impacting load, strong vibration or turning force, may damage the locking mechanism or reduce its life. 2. Consider stopping accuracy and the amount of over-run when an intermediate stop is performed.
There may be large variations depending on the surrounding environment (variations on the order of 30%).
My = 0.5 x 9.8 (10 + 11)/1000 = 0.11 A3 = 11 May = 1 x 1 x 9.14 = 9.14 Mymax = 9.14 K = 1 = 1 2 = 0.11/9.14 = 0.012 Examine Mr.
If the tightening torque is insufficient, the fittings may become loose. When connecting piping to the product, a spanner should be used on the metal piping attachment only. Using a spanner on other parts may damage the product. Avoid any sealing tape from entering inside the piping. Ensure that there is no leakage from loose piping.
If the tightening torque is insufficient, the fittings may become loose. When connecting piping to the product, a spanner should be used on the metal piping attachment only. Using a spanner on other parts may damage the product. Avoid any sealing tape from entering inside the piping. Ensure that there is no leakage from loose piping.
When different bore size is set, vibration may occur or piston rod positioning may fail. 15 11. Operation Mode and Functions This model can set the JOG operation, Calibration and Emergency stop by Air Servo Cylinder signal input and HART communication. The operation with each method is explained below. 1.
The product specified here may become unsafe if handled incorrectly. The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced. 3.
While the product shipped has been applied specified paint and surface treatment, take care that inappropriate storing environment may cause generating rust. -5- 5. Precautions in using !
The monitor and panel mount adapter may be damaged. -10No.SFOD-OMO0004-B Wiring Connection Connections should only be made with the power supply turned off. Use separate routes for the Electrostatic Sensor Monitor wiring and any power or high voltage wiring. Otherwise, malfunction may result due to noise.
If the tightening torque is exceeded the mounting screws may be broken. Never mount a product in a location that will be used as a foothold. The product may be damaged if excessive force is applied by stepping or climbing onto it. Wiring Avoid repeatedly bending or stretching the cables, or placing heavy load on them.
The warranty period of the product is 1 year in service or 1.5 years after the product is delivered, whichever is first.2) Also, the product may have specified durability, running distance or replacement parts. Please consult your nearest sales branch. 2.
If any mechanical interference, eccentric load, or overload occurs, this may cause the cylinder to deform or break. Remove such adverse factors. 4
The flatness of the mounting face may deteriorate, the guide's deviation range may increase and the sliding resistance may become greater. L L 3. Do not allow hands or fingers near the cylinder during its operation. Your fingers may be caught between the body and the plate. If you need to come near the cylinder during its operation, install a cover on the cylinder.
When the finger opening/closing speed is set as the total stroke of 0.2 seconds or more, it may cause the product to stick or completely stop its movement. MHY MHW Operating Environment -X Caution MRHQ Use caution for the anti-corrosiveness of the cross roller section.
(Using outside of the operating limit may give an adverse effect on the service life such as looseness in the guide unit and a loss of precision.) RS Q G RS H A RZQ MI W S 5. Take care not to scratch or gouge the sliding portion of the rod. This may cause a malfunction or shorten the units life. CEP1 CE1 6.
Switch 5 to 24VDC Load current (1C): 100mA, Internal voltage drop: 0.8V or less Load current (1C): 40mA, Internal voltage drop: 0.4V or less Specifications Note) When the work load exceeds 15kg, the speed may be limited. Contact SMC in this case.
At higher temperatures, the tubing may fold at more than the minimum bending radius. 4. Store away from direct sunlight in a location at no more than 40C. 1981-2000 Reprint May 2000 6
(Excessive force in the direction of rotation applied to the piston rod may damage the internal mechanism.)