Series 10-MGF ø40, ø63, ø100 Guide Table The flatness of the mounting face may deteriorate, the guides deviation range may increase and the sliding resistance may become greater. L L 3. Do not allow hands or fingers near the cylinder during its operation. Your fingers may be caught between the body and the plate. If you need to come near the cylinder during its operation, install a cover on the cylinder.
(mm) E1 = E3 = The standard chamfer may not be altered depending on the type of machining required.
CB = CA The standard chamfer may not be altered depending on the type of machining required. Equal dimensions are indicated by the same marker. (If not specifying dimension CA, indicate * instead.)
CRB2 CRBU2 The standard chamfer (mm) C1 = C may not be altered deE1 = E3 = Y L2 max (mm) Size L4 D2 pending on the type of CRB1 machining required. 10 3 4 to 8 Y 2.5 L2 + 1.5 X L1 max L3 D1 Size D1 = L4 = L2 = Y = C2 15 3 to 4 4.5 to 9 Y 3 L2 + 1.5 3 10 4 to 14 X-2.5 L1 + 1.5 C1 MSU The standard chamfer may not be altered depending on the type of machining required. 20 3 to 5 5 to 10 Y 3.5
They may vary significantly with ambient environments.
Design External Pilot Warning Extended periods of continuous energization Warning Pilot port piping If a valve is continuously energized for long periods, heat generation of the coil may result in reduced performance and shorter service life. This may also have an adverse effect on the peripheral equipment in proximity.
Extended periods of continuous energization If a valve is continuously energized for long periods, heat generation of the coil may result in reduced performance and shorter service life. This may also have an adverse effect on the peripheral equipment in proximity.
Extended periods of continuous energization If a valve is continuously energized for long periods, heat generation of the coil may result in reduced performance and shorter service life. This may also have an adverse effect on the peripheral equipment in proximity.
The product specified here may become unsafe if handled incorrectly. The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced. 1.
Avoid connecting ground lines to piping, as this may cause the electric corrosion of the system. 3. Tightening Tighten the fitting or female thread as follows. After tightening, confirm that there is no leakage from the fitting.
Please be aware that the workpiece may touch the gripper before using. Depending on the size of the concave/convex surfaces, it may be impossible to lift the workpiece. It is necessary to use an appropriate supply pressure and an adequate safety factor according to the workpiece mass.
If emitter is damaged, it may interfere with the specified function and performance, and may also cause operation failure and accident. Warning 1. Operate in an environment in the specified ambient temperature and fluid temperature ranges (0 to 55C). Avoid sudden temperature changes even within specified temperature range, as it may cause condensation. 2.
. : In some cases even when the fluid is compatible with the material, it may still permeate from the components and effect other materials. PVQ VY1 Note 1) Since static electricity may be generated, implement suitable countermeasures.
If an N.O. auto drain (symbol: D) is used when the compressor is for 2.2 kW or less, pressure inside the mist separator may not increase and remain in the state of blowing off. Auto drain with differential pressure type can be used in 2.2 kW or less. 1. Depending on the model and operating conditions, the oxygen ratio of the outlet air may drop below the prescribed standard.
This product must not be installed and used on board a conveyance such as a vehicle or a vessel, as it may become damaged due to vibration. If it must be used in such a manner due to unavoidable circumstances, please contact SMC beforehand. 1.
(mm) E1 = E3 = The standard chamfer may not be altered depending on the type of machining required.
(mm) E1 = E3 = The standard chamfer may not be altered depending on the type of machining required.
When the operating pressure is low, low speed operation may not be stable depending on a load condition. Besides, the maximum speed may be restricted depending on a pneumatic circuit, or operating pressure. 20When ordering foot bracket, order 2 pieces per cylinder. Parts belonging to each bracket are as follows.
(Assuming approximately 30% dispersion) There may be the case to change substantially depending on an ambient environment.
(Using outside of the operating limit may give an adverse effect on the service life such as looseness in the guide unit and a loss of precision.) RS Q G RS H A RZQ MI W S 5. Take care not to scratch or gouge the sliding portion of the rod. This may cause a malfunction or shorten the units life. CEP1 CE1 6.