VY511, VYU5 As a result, the cylinder actuates. For this reason, when a workpiece must be lowered, use a cylinder with a built-in brake mechanism so that the cylinder will not actuate.
Do not use this product on board a vehicle or a vessel. This product must not be installed and used on board a conveyance such as a vehicle or a vessel, as it may become damaged due to vibrations. If it must be used in such a manner due to unavoidable circumstances, please contact SMC beforehand. Employ a safe design, so that the following type of unexpected conditions will not occur.
-X 21 MXH Series Table Displacement Table Accuracy Table Displacement due to Roll Moment (Reference) Stroke (mm) Traveling parallelism 5 to 30 0.05 mm or less 40 to 60 0.1 mm or less Table displacement (at A) when a load acts upon section F at the full stroke of the Compact Slide A F Mr A Values when no load and no pressure applied.
Leakage voltage Particularly when using a resistor in parallel with a switching element and using a C-R element (surge voltage suppressor) to protect the switching element, take note that leakage current will flow through the resistor and C-R element, etc., creating a danger that the valve may not shut OFF.
No code A 1) Only available with AP501.
Passage Indicator light Single Indicator light Latching A-C ON (Set) Passage A-C ON Orange P A P A Orange OFF A R B-C ON (Reset) A R Green 2.9-4 Series VQ100 Caution Caution How to Use of Multi-connector (For plug-in manifold: For VV3Q11) How to Connect/Disconnect DIN Rail qConnecton/Disconnection of Plug Removing 1) Loosen the clamp screw of the end plate on both sides.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
Direction Note) Values for 5 stations manifold with a 2 position single type valve.
Use a cylinder with a built-in cushion mechanism. When a driven object is stopped, ensure the impact force of the object being transferred to the floating joint is prevented by using a cylinder with a built-in cushion mechanism (rubber cushion or air cushion). To stop the cylinder at the intermediate position, use an external shock absorbing mechanism such as a shock absorber.
Example of a Basic Circuit Diagram Two Hand Control Valve Push button operated valve Cylinder Air operated valve Push button operated valve 1682 Two Hand Control Valve VR51 Series Construction q t !1 i !8 y e !0 P1(11) port u R(4) Exhaust port r !5 o !7 A(2) port P2(12) port w !2 !6 !4 !
Please note that the graph should only be used as a guide, as there is a tolerance of about 10% in the clamp cylinder body.
that has a weight that is proportionate to the gripping force.
Set the operating pressure using the graphs as a guide.
Use a tightening torque of 0.05 to 0.1 Nm. As a rough guide, tighten the screw an additional 90 after feeling a tight resistance. As a rule, it should be turned about 90 beyond the point at which tightening can be felt. 0.5 0.2 0.3 MHL2-20D 0.5 0.2 0.2 MHC MHL2-25D 0.2 0.1 0.2 MHL2-32D 0.4 0.4 0.7 MHT MHL2-40D 0.2 0.4 0.7 MHY MHW MRHQ Misc.
Options Element sealing method Flat gasket (D.O.E) 1 N/A Bracket Quick plug Nil B P Housing material A square plug set is normally used for the drain unit. Cover SUS304 Case SUS304 Symbol 0 3 Quick Change Filter Series FQ1 Construction AIR VENT y Plug u O-ring w Cover INLET OUTLET t Element r O-ring e V-band i Upper element holder q Case o Lower element holder !
Open the sealed package inside a clean room. These products are packaged in sealed double packaging in a clean room. It is recommended that the inside packaging be opened in a clean room or other clean environment. 2. Flush out the piping. ITV IC ITVH ITVX Connect these products to piping only after it has been flushed and cleaned properly.
In the manifold specification sheet, specify the position where the block assembly is mounted. 13.1 3.4 Mounting hole Intermediate block assembly 2 (A) 2 (A) Clip 5 11.5 Gasket 4-11-14 Series S070 Exploded View of Separable Base Base mounted/SS073A-C Exploded View of Separable Base u i w r t q e !0 y !
Detaching To detach a socket from a connector, pull out the lead wire while pressing the sockets hook with a stick having a thin tip (about 1 mm). If the socket will be used again, first spread the hook outward.
(Pressure may be applied to any port : P, R, A) 4 Common Exhaust Valves can be ordered with a common exhaust port for the pilot and main valve.The Common exhaust provides for a cleaner operating environment by exhausting the pilot air through the main valve body rather than directly to atmosphere.
This regulator cannot be used as a check type regulator to be installed between a solenoid valve and an actuator. It can cause breakdown and malfunction. 7.