Series MXS 13- ø6, ø8, ø12, ø16, ø20, ø25 22- Air Slide Table Otherwise particle generation may occur because the prepared hole of the mounting screw penetrates the body. Contact SMC for more information. Dust plug Dust cover Cylinder bore size (mm) 25 Extension end stroke adjuster mounting screw (Generates particles because it penetrates to the body.)
However, smooth acceleration and deceleration may not be obtained by these speed controllers. 3. For installation other than horizontal mounting, it is recommended to use a system with reduced pressure supply circuit on the downward side.
If mounted in the wrong direction, the equipment to be connected may cause malfunction. Refer to external dimensions in pages 3-2-4 to 3-2-10, and then mount it. VFN 48 V DC None Z Precautions Plug a connector in or out vertically, never at an angle. How to Calculate the Flow Rate S 6 V For obtaining the flow rate, refer to page 3-1-10.
If mounted in a wrong direction, the equipment to be connected may result in malfunction. Refer to pages 1413 to 1417 for external dimensions in mounting.
If mounted in the wrong direction, the equipment to be connected may cause malfunction. Refer to external dimensions in pages 1423 to 1428, and then mount it.
Caution Light/Surge Voltage Suppressor Piping If supply port air pressure drops to less than 0.2 MPa, the valve may malfunction. In such a case, use external pilot type. (When throttling IN port, or operating with OUT port open to the atmosphere or in a similar operation.)
In addition, changes in the force on the cylinder parts may cause dangerous movement to occur with forceful impact. 120 mm or less 2. Affix a protective cover in places where there is a danger of personal injury. A large gripping force is generated during clamping. If there is a possible pinching hazard, design the structure to avoid contact with the human body. 3.
Note 3) If the temperature at the gate exceeds 60C, the operating temperature at actuator may go beyond the range. In this case, cool the actuator part. Note 4) This shows the time after the switching valve activates and causes the gate to open and close. Note 5) The holding function of the seal is not guaranteed when the gate is clamped.
It may cause damage to the body. (Alcohol, acetone, etc. also cause damage, so be sure for the product not to be close to them.) Note 2) Do not use it in a line that is kept pressurized because it could cause the body to break. Large filter element surface Mountable in any direction Bracket Set Part No.
It may cause damage to the body. (Alcohol, acetone, etc. also cause damage, so be sure for the product not to be close to them.) Note 2) Do not use it in a line that is kept pressurized because it could cause the body to break.
Tightening with a torque outside of the specified range may cause malfunction.
Tightening with a torque outside of the specified range may cause malfunction.
Otherwise, noise may cause malfunction. When induction nOise IS expected to be generated from piping,ground the piping. G)The tensile strength of the cord is 49N(5kgf).Tensile strength greater than thai will cause trouble. Hold the main unit when handling the switch. Quality of operating fluid Sections in contact with flUId are made of SUS630 (pressure sensor) and SUS304 (fitllng).
Signal noise may cause malfunction. Dry air (VII induction noise is expected via the piping connectiOf'l. make a groundmg connection lor the piping. Drain-containing alf 0 Hydraulic fluid (JIS-K(213) ~ Silicon oil (JIS-K221 3) G ;])The tensile strength of the cable lead is 49N Lubricating oil (JIS-K630l ) '' (Skgf). Avoid damage by always handling the switch by the main housing.
Fig. 1 = 0.7 or more Fig. 2 = 0.5 or less Fig. 3 = 1 or less Note) For dynamic operation, the load ratio may be set even lower if it is particularly necessary to operate the cylinder at high speeds.
Excessive load on the lever section may cause malfunction. Note 2) On the 20 and 32 type, the drag of the shock absorber cannot be changed, but the stroke of the shock absorber is possible to change by adjusting height of the adjustment dail. Be sure to read before handling. Refer to p.0-39 to 0-46 for Safety Instructions and common precautions on the products mentioned in this catalog.
(Assuming approximately 30% dispersion) There may be the case it will vary substantially depending on an ambient environment. Minimum Stroke for Auto Switch Mounting (mm) Auto switch Applicable auto switch model No. of auto switches mounted D-Z7, D-Z8 D-Y7W, D-Y7WV D-Y59, D-Y69 D-Y7P, D-Y7PV 5 10 5 10 10 15 1 pc. 2 pcs.
If the direct acting guide is directly connected in operation, it may lead to malfunction or reduced service life.
If not operated in accordance with the above precautions, the cushion valve may be ejected from the cover when air pressure is supplied. CJ1 1. Avoid using the air cylinder in such a way that more than allowable rotational torque would be applied to the piston rod. If rotational torque is applied, the non-rotating guide will deform, thus affecting the non-rotating accuracy.