Series MHZ2 11- ø10, ø16, ø20, ø25 22- Air Gripper Flat finger [3] 4 x MM thread depth L Thread for mounting attachment K J A A D G B D B K J F C S W O (mm) Weight (g) F G Open Closed 2 2.5 3 4 L MM J K D C B Model A W MHZ2-10D3 1), 2) 11221122112211220 -0.05 0 -0.05 0 -0.05 0 -0.05 +0.5 +0.3 +0.5 +0.3 +0.5 +0.3 +0.5 +0.3 +0.025 0 +0.025 0 +0.025 0 +0.030 0 +2.2 0 +2.2 0 +2.3 0 +2.5 0 60 125 250 450 5 6 8 10 M2.5 x 0.45 M3 x 0.5 M4 x 0.7
Select the point of contact A of inlet pressure and max. air capacity in the graph. 2. AME650 is obtained when the max. flow line is above the point of intersection A in the graph. Note) Make sure to select a model that has the maximum flow rate line above the obtained intersecting point.
Select the point of contact A of inlet pressure and max. air capacity in the graph. 2. AMF650 is obtained when the max. flow line is above the point of intersection A in the graph. HA AT ID Max. air flow rate (m3/min (ANR)) AMG Note) Make sure to select a model that has the maximum flow rate line above the obtained intersecting point.
Select the point of contact A of inlet pressure and max. air capacity in the graph. 2. AMD650 is obtained when the max. flow line is above the point of intersection A in the graph. Note) Make sure to select a model that has the maximum flow rate line above the obtained intersecting point.
Select the point of contact A of inlet pressure and max. air capacity in the graph. 2. AMG650 is obtained when the max. flow line is above the point of intersection A in the graph. HA AT Max. air flow rate (m3/min (ANR)) ID Note) Make sure to select a model that has the maximum flow rate line above the obtained intersecting point.
Contact P/A if the product will be used in an application with a high frequency of operation. 1. Do not subject the gauge to impacts, such as dropping, during transportation and mounting. This can cause loss of indication accuracy. 2. Do not use in locations with high temperature and humidity. This can cause malfunction. 3.
Affix a safety cover in places where there is a danger of personal injury. 4. Make sure that the offset of the clamping position is within 15 mm as shown in the figure below. A large gripping force is generated during clamping. If there is a possible pinching hazard, design the structure to avoid contact with the human body. Allowable offset 15 mm Caution 1.
Select the point of contact A of inlet pressure and max. air capacity in the graph. 2. AMH650 is obtained when the max. flow line is aboveabove the point of intersection A in the graph. Note) Make sure to select a model that has the maximum flow rate line above the obtained intersecting point.
Note) Make sure to select a model with the maximum air flow rate line that is located above the obtained intersection point. A model with the maximum air flow rate line that is located below the obtained intersection point will have an excess flow rate, and will not satisfy the specifications.
Auto switches marked with a "" symbol are produced upon receipt of order. Note 1) Take note of hysteresis with 2 color indication type switches.
Please exercise caution when using this item in a clean room. There is a possibility of plasticizer and other materials precipitating on the tube surface and detracting from the cleanliness level of the room.
Further, use DC power with sufficient capacity and a low ripple.
Contents 150 NC1AKW150-PS 200 NC1AK200-PS-XC11 200 NC1AKW200-PS 250 NC1AKW250-PS
10%Power supply voltage 24 VDC type: 0.12 A or less Note 6)Power supply voltage 12 to 15 VDC type: 0.18 A or lessSet pressure ?13.3 kPa?101 kPa?1.3 to ?
10%Power supply voltage 24 VDC type: 0.12 A or less Note 6)Power supply voltage 12 to 15 VDC type: 0.18 A or lessSet pressure ?13.3 kPa?101 kPa?1.3 to ?