Non-contact Gripper Description Material Note 1 Body (R, L) Aluminum alloy (Black hard anodized) XT661-2A, 3A w 2 Body M Aluminum alloy (Black hard anodized) 741 XT661 Series Construction [Bernoulli Type] Size: 40 Size: 60 Size: 80, 100 A-A A-A A A q w w i u y t e e A B i A B r A A q A-A B-B t y u q u y t e w r r Size: 120, 150 B-B A-A A B B q r e w t y u i r C-C C C r A Guide assembly Component Parts A-A o
In addition, it can relay output as an alarm contact output when an alarm is generated. Alarm Alarm code Alarm description Operation status Main reason AL0 Memory error Stop There is an abnormality with the memory data in the controller due to a high level of noise. AL1 Controller error Stop There is an abnormality with the data in the controller due to a high level of noise.
Perform periodic inspections, and if any leakage is detected, replace with a new product immediately. When the insert and miniature fittings are used over extended periods of time, it may cause leakage due to the material deterioration of age. In such a case, give an additional tightening to the tube connection part.
AC20-A AC25-A AC30-A AC40-A AC50 VHS20 VHS30 VHS40 VHS50 Single Action Series VHS20/30/40/50 Double Action Series VHS2510/3510/4510/5510 CAT.NAS13-10A Single Action Series VHS20/30/40/50 Double Action Series VHS2510/3510/4510/5510 Single Action Series VHS20/30/40/50 Double Action Series VHS2510/3510/4510/5510 Lightweight Lightweight Resin handle and bonnet is standard. 60% Lighter Resin handle
MXW MXP Air-hydro Copper Free MG Low hydraulic pressure cylinder under 1.0MPa Through the concurrent use of a CC Series air-hydro unit, it becomes possible to operate at a constant or low speed or to effect an intermediate stop, just like a hydraulic unit, while using pneumatic equipment such as a valve.
A wireless slave can then be registered to the dummy area at a later time, without having to change the I/O map Dummy slave E Export Function to save the configured values of a wireless unit by exporting them to a PC. F Fieldbus Network protocol to establish digital communication between an automated industrial system such as a measurement tool or manipulation tool and a PLC.
Block off the heat with a cover, etc. 5. Do not use in locations where static electric charges will be a problem. Consult SMC regarding use in this kind of environment. 6. Do not use in locations where spatter occurs. There is a danger of spatter causing a fire.
Block off the heat with a cover, etc. 5. Do not use in locations where static electric charges will be a problem. Consult SMC regarding use in this kind of environment. 6. Do not use in locations where spatter occurs. There is a danger of spatter causing a fire.
A wiring example of multiple controllers (3 pcs.) connected to an upper level device is shown below.
A wireless slave can then be registered to the dummy area at a later time, without having to change the I/O map Dummy slave E Export Function to save the configured values of a wireless unit by exporting them to a PC. F Fieldbus Network protocol to establish digital communication between an automated industrial system such as a measurement tool or manipulation tool and a PLC.
Do not Do not use the product in a place where static electricity is a problem. Otherwise failure or malfunction of the system can result. Do not If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system. Check the product for proper operation. Otherwise malfunction can result, causing an accident.
(Ex. : 1:Normal) C o n t r o l O p e r a t i o n M O D E < 1 : N o r m a l Function : Selects control operation mode among them below 0 : Stop of control (Pump Stop) 1 : Normal (normal control operation) 2 : AT (auto tuning) 3 : Learning control (Learn) 4 : External tune control (External) When a learning control and an external tuning control are selected, measurement temperature (#2) of
Operation of an auto switch may become unstable by the effect of a magnetic substance. There is no problem if a magnetic substance is close to any side where an auto switch is not mounted.
When the product is Unevenness of a workpiece or base mounted on the body of the product may cause play in the guide and an increase in the sliding resistance. 10. When mounting the product, keep a 40 mm or longer diameter for bends in the cable. 11. Do not hit the table with the workpiece in the positioning operation and positioning range. 12.
Therefore, even within a given allowable kinetic energy level, there is an upper limit to the amount of the load that can be sustained. 11.Use a balanced circuit in which lurching of the cylinder is prevented.
Using an electronic type pressure gauge is recommended, depending on the situation. 727 ARM11B Series Construction OUT IN SMC K P C U O S H L e t A-A A w y r i !0 u !1 q SMC o A Component Parts Description Replacement Parts Part no. Material Note Material No. Description No.
size A C D E G H J 1(P) 2(A) 3(R) AV2000-m02-1 to 4G(Z)m-A 1/4 1/4 1/4 66 47 24.5 40 33 Width across flats 22 30 AV2000-m02-5 to 6G(Z)m-A AV3000-m03-1 to 4G(Z)m-A 3/8 3/8 3/8 76 50 29.5 40 38 Width across flats 24 35 AV3000-m03-5 to 6G(Z)m-A AV4000-m04-1 to 4G(Z)m-A 1/2 1/2 1/2 98 56 39.5 52 49 Width across flats 30 33 AV4000-m04-5 to 6G(Z)m-A AV5000-m06, 10-1 to 4G(Z)m-A 3/4, 1 3/4, 1 3/
Block off the heat with a cover, etc. 5. Do not use in locations where static electric charges will be a problem. Consult SMC regarding use in this kind of environment. 6. Do not use in locations where spatter occurs. There is a danger of spatter causing a fire.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
External pilot type R (2) B C A Note 1) Option Note 2) For details about external pilot specifications, refer to page 4-14-40.