XLC-25,40 ∗ -F7NJ ∗ - ∗ Series Heater specifications Item XL-25 XL-40 Rated voltage of the heater 90 to 240 ACV Heater assembly number XLA25-60S-1 No. of heater assemblies 1 pc. H 4 S y m b o l consumption (W) 100 VAC 200/40 Initial power / Power 200 VAC 800/40 Heater assembly number XLA25-60S-1 XLA25-60S-2 No. of heater assemblies 1 pc. 1 pc.
Use it when you want to remove water but air as dry as that from an air dryer is not necessary, or when a power supply for an air dryer is not available, etc.
Use it when you want to remove water but air as dry as that from an air dryer is not necessary, or when a power supply for an air dryer is not available, etc.
The product does not have an explosion proof construction. Be sure to take measures to prevent the area around the product from becoming filled with an explosive gas, when using an explosive fluid. 394
[mm] m L2 L1 Item Load factor an Note 1.
[mm] m L2 L1 Item Load factor an Note 1.
How to Order M Type Connector Assembly ON OFF ON OFF Lead wire length Positive common specifications Nil 6 10 15 20 25 30 50 SX100-40-4S300 mm 600 mm 1000 mm 1500 mm 2000 mm 2500 mm 3000 mm 5000 mm For single solenoid: Normal operating state. Switching of valve is based on an electric signal from the connector.
In the case of MVGQM50-40 st, an interface of 10 mm wide is installed inside of the MVGQ50-50 st, and thus the full length dimension of the body is the same as 50 st. 20, 30, 40, 50, 75, 100 125, 150, 175, 200 25 M L MVGQ M L 32, 40 25, 50, 75, 100, 125, 150, 175, 200 MVGQ 50, 63 10-16-9 10 Series MVGQ Weight (kg) Standard stroke (mm) Bearing type Bore size (mm) Model The allowable lateral
Connector pin numbers PF2W504T--1 PF2W520T--1 PF2W540T--1 PF2W504T--2 PF2W520T--2 PF2W540T--2 4 0.5 4 0.5 4 3 16 2 16 2 40 5 40 5 2 1 Pin no.
If 12VDC specifications are required, enter "12" at the end of the assembly part number. 1 2 1 2 P N D side SZ3000-40-6A-D For flat cable 20 pins SZ3000-40-5A-D 1 2 1 2 P N D side SZ3000-40-8A-D For flat cable 10 pins SZ3000-40-7A-D A connector block assembly can be shipped as an assembly only in the case of double wiring.
For connection with a load having an external support/guide mechanism, select an appropriate connection method and perform careful alignment.
Arrange so that maximum load will be 40% for theoretical force of 20, 50% for 32, 55% for 40 and 60% or less for 50, respectively.
style Double clevis style B L F G D Note) 10 16 20 25 28 10 mm 16 mm 20 mm 25 mm 28 mm 16 10, 20, 30, 40, 50, 60 20 10, 20, 30, 40, 50, 60 25 10, 20, 30, 40, 50, 75, 100 28 10, 20, 30, 40, 50, 75, 100 Note) Available only for MQQL.
28 10, 20, 30, 40, 50, 75, 100 Note) Available only for MQQL.
In addition, it can relay output as an alarm contact output when an alarm is generated. Alarm Alarm code Alarm description Operation status Main reason AL0 Memory error Stop There is an abnormality with the memory data in the controller due to a high level of noise. AL1 Controller error Stop There is an abnormality with the data in the controller due to a high level of noise.
Vibration (Supply pressure: 0.1 MPa) Lifting force (N) 0.5 30 Cyclone type 0.4 ZP3 0.3 0.01 mm or less 20 0.2 Amplitude (mm) ZP3E 0.1 10 0 Low profile cyclone type ZP2 0.1 0 20 40 60 80 100 0 0.2 ZP2V Size (mm) 0.3 Totaled 5 size: 20/40/60/80/100 0.4 ZP 0.5 0 0.5 1 1.5 2 2.5 Low profile cyclone type Totaled 6 size: 40/60/80/100/ l120/l150 ZPT ZPR Time (sec.)
Contents 40 MGF40-PS Items !
In such a case, give an additional tightening to the tube connection part. If leakage still occurs after giving an additional tightening, replace the fitting with a new product. For other precautions, refer to Fittings & Tubing Precautions. When using the fluoropolymer fittings, refer to the precautions on pages 445 and 446. Select the size after confirming O.D. and I.D.
Furthermore, an abnormal temperature rise due to adiabatic compression can cause tubing to burst. Note 3) The minimum bending radius indicates the value at a temperature of 20C (68F) with an outside diameter rate of change of 10% or less. At higher temperatures the outside diameter rate of change may exceed 10% within the minimum bending radius.
Furthermore, an abnormal temperature rise due to adiabatic compression can cause tubing to burst. Note 3) The minimum bending radius indicates the value at a temperature of 20C (68F) with an outside diameter rate of change of 10% or less. At higher temperatures the outside diameter rate of change may exceed 10% within the minimum bending radius.