reduces flow setting time Connection Female Thread: Rc, NPT, NPTF Uni thread size Wrench tightening angle after hand-tightening [deg] Tightening torque [Nm] 1/8 30 to 60 3 to 5 1/4 30 to 60 8 to 12 3/8 15 to 45 14 to 16 1/2 15 to 30 20 to 22 Connection thread size Proper tightening torque [Nm] NPT, R1/8 3 to 5 NPT, R1/4 8 to 12 NPT, R3/8 15 to 20 NPT, R1/2 20 to 25 Connection Female Thread: G Chamfered area for female
to +80C 20 to +70C 40 to +85C 25 to +90C Cable 20 to +70C Min. bending radius (Fixed) 67 mm 60 mm Protection class 100 IP67 (Only with screw tightened) Allowable repeated insertion/withdrawal 200 Material of knurl Zinc die-cast (Nickel plating) Brass (Nickel plating) Zinc die-cast (Nickel plating) Contact (Surface treatment) CuSn (Au plating (Ni underplating)) Phosphor bronze (Au plating
Note 2) At oil mist density of 30 mg/m 3 ANR is blown out by compressor. Refer to Made to Order Specifications on page 14-20-55.
RHC Air balance Supply pressure OSet the supply pressure at 0.25 to 0.5MPa. If setting at less than 0.25 MPa. malfunction of the release brake may occur. OIf air is directly supplied from main line, pressure fluctuation on the main line will directly influence to cylinder operation characteristics.
Therefore, when used at near the upper limit, the following guide will be helpful.
Therefore, when used at near the upper limit, the following guide will be helpful.
To install/remove the product, use an appropriate wrench to tighten/loosen at the supplied nut on body B. 12. Mounting Do not apply torque at other points as the product may be damaged. Rotate body A manually for positioning after installation. Warning 1.
80 mA load current) Response time 2.5 ms or less (response times available for anti-chattering function: : 20, 100, 500, 1000 or 2000 ms) Short circuit protection Provided Repeatability 0.2%F.S.1 digit Hyster esis Hysteresis mode Adjustable (can be set from 0) 1 Display 3 1/2 digits, 7-segment display, color display (Red) Indicator accuracy +/-2%F.S., +/-1 digit (at ambient temperature 25
Speed Controller Cylinder Solenoid valve Tubing Silencer Max. return speed (mm/s) 10 20 30 6 ASD230FM CJ2 SYJ500 TU0604 1 m AN11001 10 16 Cylinder size 20 ASD330FM CM2 SYJ700 TU0604 1 m AN11001 Cylinder size 25 32 Values are measured at 0.5 MPa and 20C.
DAVor less 15Vrms or less _ Lea _ k '-, age current 10,UA or less at 24VDC 1 .SmA or less At OFF, the red color LED lights Indica,tor lamp At ON, the green color LED lights At OFF, the red coil)( LEO lights --f Operating time 1 m sec or less 2m sec or less D-PHl Lead wire entry Grommet ~---f-~~~ O~PH1L(Z ) Flame retardIng and oil proof Vinyl Flame retarding and oil proof vinyl Lead wire
Pull the AUTO-SHIFT input to GND for at least 10 [ms]. The auto shift feature is activated by the rising flank of the auto shift input. The Display and Set points are now based on the pressure at the moment of release after auto shift input. Example: The figure below is based on the condition of set values as P1 = 40 [kPa] and P2 = 20 [kPa].
) (Example) To get pressure drop at 0.3 MPa of air pressure, 5 m3 /min (ANR) of air flow and model HAW75-20, use 0.0065 MPa at 0.7 MPa from the table and convert P1 to 0.3 MPa.
20 20 20 20 20 20 20 20 63 76 76 90 90 106 106 122 160 , , 1 4 3 8 40 40 50 50 55 55 65 85 , AMH250 1 2 3 8 1 2 , AMH350 3 4 1 2 3 4 , AMH450 1 1 1 1 AMH550 AMH650 3 4 1 2 , , 14-20-34 6 Micro Mist Separator with Prefilter Series AMH AMH850 Dimensions Accessory D: With auto-drain (N.O.) for AMD850 female thread Option T: With element service indicator Courtesy of Steven Engineering, Inc.
o.s, ercept dyo6.. op.Btins PEssubs: 28" vacuum 0 PStc {20 Kgt/cnf)' NVS/tl|-4 Prssure Fanoe: 28" vacul 3@ rlc {20 Kgrcnti) Lakage: Irort lo pon (nt.maD not to .xce.d 0.005 coblc fl pr hinut at 1@ PstG (6.7 toam) Mel4islr: all houshc !6n. atumhum d|6 cas|ngg $oor arld stc@ a40F 61atnt6r. p.5rlvated ad hdtJoai.d lo 5a52 FE*wdl c 96* orlnot Blra N, sp&.r end dl.nl hou3in!
Panel cut dimension 2 x 3.2 16.5 14.5 11 8.2 20 2 x 3.2 2 x 3.2 M3 thread hole 8.2 8.2 P U P S U H S H L O L C O K C K R V R S W V X S W T 19 T X 19 L2=50+T+X L2=50+T+X L1=50+R+V 14 L1=50+R+V 14 Pressure gauge (Accessory) 50 Pressure gauge (Accessory) 50 55 (at knob locked) 55 (at knob locked) IN OUT IN OUT 41.5 43.5 U Y 4 25 6 25 U Y 14 14 SMC SMC 2 x 3.2 2 x 3.2 42 42 IN side OUT side IN
Applicable cylinder bore size (mm) 3.2 Metric size Inch size Model 6 8 4 1/8" 5/32" 3/16" 1/4" 5/16" 6, 10, 16, 20 AS1001FM 20, 25, 32 AS2001FM 20, 25, 32, 40 AS2051FM Specifications Proof pressure 1.5MPa Maximum operating pressure 1MPa Minimum operating pressure 0.1MPa Ambient and fluid temperature 0 to 60C Number of needle revolutions 10 revolutions (20 revolutions Note 1) ) Applicable
80 mA load current) Response time 2.5 ms or less (response times available for anti-chattering function: 20, 100, 500, 1000 or 2000 ms) Short circuit protection Provided Repeatability 0.2%F.S.1 digit Hysteresis Hysteresis mode Adjustable (can be set from 0) 1 Display 3 1/2 digits, 7-segment display, colour display (Red) Indicator accuracy +/-2%F.S., +/-1 digit (at ambient temperature 25+
Insert each lead wire into the corresponding connector number by following the chart provided below. 20 mm or more Connector no.
Bank Point Home position sensor position 0. 1. 0 0 0 0 0 0 Moves to the motor side at home position return speed Decelerates and stops at the home position sensor ON position Moves to the end side at low speed Moves and stops at 16 pulse position from the home position sensor OFF position Coordinate attribute Coordinates Speed pattern Operating procedures 1.