C95 Balance the load by adjusting the air pressure in the front and rear sides of the cylinder with the load connected to the cylinder and the lock released. Lurching of the cylinder when unlocked can be prevented by carefully adjusting this air balance. Note) Can be used if all of the generated moment is absorbed by an effective guide. 2.
An autoswitch can be mounted to indicate operation of the buffer, operated by a magnet on the piston. By reversing the direction of the switch, NO or NC operation is achievable.
It then acts on diaphragm B as nozzle back pressure, the main valve is pushed down by the generated force, and the supply pressure flows out to the downstream side. The air pressure that flows in acts on diaphragm C. While opposing the force generated by diaphragm B it also acts on diaphragm A, opposing the compression force of the setting spring and becomes the set pressure.
Do not rotate the product by the indicator part. Use a wrench for mounting the product. Otherwise, it may cause damage to the product. 601
Balance the load by adjusting the air pressure in the front and rear sides of the cylinder with the load connected to the cylinder and the lock released. Lurching of the cylinder when unlocked can be prevented by carefully adjusting this air balance. Note) Can be used if all of the generated moment is absorbed by an effective guide. 2.
Uni thread H D1 D2 L1 L2 L5 A Max.
Products approved by CSA or UL standards are accepted in most states and governments beyond question.
T M5 type H (width across flats) Applicable tubing O.D. d A A4 D1 L3 D2 M1 L1 T L2 Model Weight (g) Note 2) Tubing O.D. d T H D1 D2 L1 L2 L3 M1 L4 Max.
The port A pressure is fed back to the control circuit by the pressure sensor.
5 15-17-5 6 Series AS-FPQ/FPG Dimensions H (width across flats) Applicable tubing O.D. d A L4 D1 L3 D2 M1 L1 L2 T M5 type H (width across flats) Applicable tubing O.D. d A A4 D1 L3 D2 M1 L1 T L2 Model Weight (g) Note 2) Tubing O.D. d T H D1 D2 L1 L2 L3 M1 L4 Max. Min. Max. 1 2 Min.
When you begin to feel that the screw is being tightened, turn it further by 90. MHKl2-12 0.4 0.4 1.6 MHKl2-16 0.4 0.4 1.6 MHKl2-20 0.4 0.4 1.6 MHKl2-25 0.4 0.4 1.6 Protrusion of Auto Switch from Edge of Body The protrusion of an auto switch from the edge of the body in the table below. Use the table as a guideline for mounting.
(Normally Open) merely by turning over the switch cover.
MHS 0.3 to 0.5 mm MHC MHT MHY Step 5) Move the auto switch in the opposite direction 0.3 to 0.5 mm in the direction indicated by the arrow from its location when the indicator light comes on again.
During an emergency when the air supply is cut off, it is used to alleviate a problem by forcibly pushing the release piston back to release the lock. However, take note that the sliding resistance of the piston rod will be high compared to unlocking with air pressure. 2.
In case of heavy soiling, wipe it off with a cloth soaked in a neutral detergent diluted with water after wringing it out thoroughly, and finish up by wiping with a dry cloth.
High vacuum settings are obtained by turning it clockwise. When setting, use a flat head screw driver which fits the slot in the trimmer, and turn it gently with your finger tips. To install the connector, hold the lever and connector unit between your fingers and insert it straight onto the pins. Then lock it by pressing the pawl of the lever into the slot on the housing.
Products approved by CSA or UL standards are accepted in most states and governments beyond question.
B Section BB A Section AA Bolt holder (movable) l2 l1 Warning Approx. 0.5 or less 1. Take precautions when your hands are near the plate and housing.
It then acts on diaphragm B as nozzle back pressure, the main valve is pushed down by the generated force, and the supply pressure flows out to the downstream side. The air pressure that flows in acts on diaphragm C. While opposing the force generated by diaphragm B it also acts on diaphragm A, opposing the compression force of the setting spring and becomes the set pressure.
MHK2-12S 120 12 9 4 9 13 76 Normally open Normally closed MHK2-16S 16 23 6 14.6 20.6 114 DL1 MHK2-20S 20 34 10 16 26 237 L2 MHK2-25S 25 58 14 19 33 443 20MHK2-12C 12 12 4 9 13 76 MHK2-16C 16 25 6 14.6 20.6 115 MHK2-20C 20 44 10 16 26 237 MHK2-25C 25 73 14 19 33 443 Series MHKL2/Long Stroke Type Note) Width at opening (mm) L2 Width at closing (mm) L1 Effective gripping force per finger (N)